3XART719GG00 Whirlpool Refrigerator - Instructions

Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.

Viewed the viedo - it showed what to do

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

I was able to replace the the shelf bars with no difficulty after finding the right parts on PartSelect. The easy to view measuring menu helped me get the right size for the fit I needed. You always worry when you don't have the item in front of you but they make it easy to gauge. I will use them again. I replaced three bars that had been driving me crazy.

I followed vidio instructions, took about 15 minutes. Fridge making great ice cubes again. Felt prouud of the repair I did being 70 years old and a female. Thank you

Just followed the video that you guys had on line . It was a very easy repair

hardest part was pulling out the refrigerator. it took about five minutes. parts fit perfectly. only thing to look for is some excess flashing on the end of the tube. easily removed with a pocket knife. simple repair.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

Removed the screw from the old tray. Attached the new tray and return the screw using a wrench to assure the screw was torqued properly.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.