3968XVB Magic Chef Microwave Oven Combo - Instructions

I can't believe how easy this was to fix! I amazingly found the part on-line at PartSelect website. I love that you pick part by size, color, etc. I didn't have a part or model number, so this made it super easy! I ordered the part and got it in the mail within 2 days....YEAH! I got my screwdriver out and attached the peice, slid the drawer back in and shazam! it was fixed! Thank you PartSelect and kudos to the person that set up the way you order your parts......awesome! Thanks!

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

Piece of cake. Removed the Phillips screw with screwdriver, placed new one on the slide and used old screw to screw it in place. Drawer does not lean to one side anymore.

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

Broken part was already removed, so I used the screw from the broken support and installed the new support. Very simple, easy, and painless.

Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

removed drawer from track replaced supports on track and one on the drawer.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.