3939731583 Kenmore Refrigerator - Instructions

water runs in now but still does not make cubes. just keeps dripping until I shut the water off.

Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0

Hi, My furnace when out when I was away, frozen water lines were repaired, but my ice maker line was turned off, the valve split open. Summer is coming I want ice! I found the right replacement, ordered it, watched the free video, did the repair. It was so easy. And I saved an expensive service call. I am drinking a soda with ice from the ice maker as I type this! Thanks for solving my problem, I will be back next time something needs a part! Bob

I first disconnected the plug from the wall outlet. I then turned off the water supply to the back of the refrigerator. I then disconnected the two lines to the water inlet valve and removed the nut that holds the bracket to the refrigerator. I removed the water valve and installed the new one the same way in about 5-10 minutes. It was very easy, but, unfortunely that was not the problem.

took water line loose at outlet valve to confirm that water was getting to valve. I ordered part and it arrived the next day. It was very simple installation took 10 minutes. Thanks to parts select, Kirk

Replaced single outlet valve for the ice maker

With help from this site, It was one of three things. I thought it might be what this site suggested the most common and it was. the valve in back of refrigerator at bottom. Water comming to it, but not getting past. Ordered part. Was here in a few days. Real easy to change out. A few screw / bolts and one wire that fit only one way. I did have to bend new bracket to make it fit. Now have lots of ice cubes!

I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.

removed old valve, installed the new one. ice maker back to making ice.

Ordered the part from "parts select". Removed old part, installed new part by unscrewing the old switch, simply cutting supply hose ...pluging in the new part and re-attaching water supply line. 10 minutes at most.

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

had to replace copper water line to valve

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.

Followed the video demo and would have been done sooner but for limited work space- narrow freezer compartment and the release tabs on the electrical plug. First home repair that the air was not blue and got done in under time allocated.

I am a 68 year old woman that had hernia surgery (6) weeks ago so my friend did the replacement. I showed him the video of how to fix it and I felt like I could have done this myself because all you had to do was loosen a couple of screws to get into the back of refrigerator and pull out the bad part. It was like plugging in my cell phone for recharging I do everyday. Unbelievely easily. The price was great also. We priced part locally and they wanted $30.00 and your part was $18.25 plus shipping. Shipping was unbelievely quick also. It was shipped within (2) days after ordering. Very satisfied.