3868XPW Magic Chef Range - Instructions

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.

i removed the two screws that holds the element in. I pulled the element out and disconnected the wires and I had to adapt a double male adapter to the wire ends and plug the wires back onto the element. The old element had male spades and the new element had female spades.

Removed the single phillips screw that held each plastic slide guide to the stove, and replaced the part reusing the screws. Was so simple I didn't even have to swear. This was my mother-in-law's stove, and she was so happy to have it repaired she's fed me twice since.

1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

Put a new one in.

swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.

I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concise diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).

replaced heat sensor