36315658890 Kenmore Dishwasher - Overview
Sections of the 36315658890
[Viewing 3 of 3]
Manuals & Care Guides for 36315658890
Click to downloadKeep searches simple, eg. "belt" or "pump".
Piston and Nut Assembly
PartSelect #: PS260690
Manufacturer #: WD24X10018
This is used for the check valve.
$30.95
Special Order
Hinge Arm Link
PartSelect #: PS259336
Manufacturer #: WD14X10009
The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In ...
$17.70
Special Order
Rinse Aid Fill Cap
PartSelect #: PS2351824
Manufacturer #: WD12X10284
This part helps keep the rinse aid the dispenser until its needed.
$78.79
Special Order
Impeller and Seal Kit
PartSelect #: PS259598
Manufacturer #: WD19X10032
This part helps stop your dishwasher from leaking. This kit includes the impeller, seal, blade, filter, skidder and skidder holder.
No Longer Available
Motor and Pump Kit
PartSelect #: PS260801
Manufacturer #: WD26X10013
This pump and motor kit replaces many old style pump and motor kits that were manufactured since 1970. The instructions are included with this kit to help you to make it adaptable to your dishwasher.
...
$275.11
Special Order
Door Latch Kit
PartSelect #: PS259293
Manufacturer #: WD13X10003
This door latch kit is used for dishwashers.
$62.07
Special Order
Detergent Cup Release Arm
PartSelect #: PS1765980
Manufacturer #: WD16X10011
This is the replacement detergent cup release arm for your dishwasher. It is made of black plastic and is sold individually. The detergent cup release arm is found on the inside of the dishwasher door...
$65.93
Special Order
Lower Spray Arm and Support Assembly
PartSelect #: PS260529
Manufacturer #: WD22X10008
This part comes with the telescopic tower.
No Longer Available
Door Gasket - White
PartSelect #: PS258654
Manufacturer #: WD08X10016
This genuine OEM dishwasher door seal gasket prevents water from leaking out of the dishwasher. If your washer is leaking from the door, check for wear on the gasket, and to ensure it is properly fitt...
$47.57
Special Order
Dishwasher Hose Clamp Kit
PartSelect #: PS270806
Manufacturer #: WH1X2036
This hose clamp kit contains two clamps. The smaller of the two is an inch in diameter while the larger of the two is two inches in diameter.
$22.95
Special Order
Common Symptoms of the 36315658890
[Viewing 10 of 10]Not draining
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher wouldn't fully drain
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. This easy repair solved the problem.
Parts Used:
-
Dan from Minnetonka, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
191 of 206 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor was getting noisier every time we used the dishwasher. We knew it was just a matter of time before it totally quit.
The most difficult part was removing the dishwasher from below the counter. Once that was complete, I simply turned the washer onto it's front surface to access the pump easier. Simply disconnected the electrical connectors, loosened the three hose clamps holding the hoses to the pump. Lastly removed a stiff arm bracket holding the pump. Reversed the order to install the new one using a longer bracket provided with the new unit. Hooked up the electrical connections last and slid the washer back in place. The washer runs like new now and is not making noise. The replacement part was a perfect match.
Parts Used:
-
Glenn from Clemmons, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
48 of 53 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher pump valve leaking at shaft
took dishwasher out- put on table to work on-removed wire brace- disconected drain outlet- disconnected top drive seal- removed wire clip connector- removed motor unit----------------
installed new motor/drain unit--used new longer wire brac used adapter to connect electical leads-
tightened clamps and bingo it worked and didnt' leak. good job on the supplying of all the necessary adapers.
installed new motor/drain unit--used new longer wire brac used adapter to connect electical leads-
tightened clamps and bingo it worked and didnt' leak. good job on the supplying of all the necessary adapers.
Parts Used:
-
richard from las vegas, NV
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set, Wrench (Adjustable)
40 of 47 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!