36314071790 Kenmore Dishwasher - Instructions

Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.

replaced the master toner relay.

Plastic contacts on knob broke off which caused the timer to not function. I tried to glue the pieces together but the repair was unsuccessful. I had the parts list from Kenmore and I went on line to order the part. I ordered the part on Wednesday and the part arrived on Friday. The part fit perfectly and now the dishwasher is oparating correctly. Thank you.

Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.

Followed easy instructions and completed repair in less than 30 minutes.

This was a 45 min project. New pump was a redesign. Match your style with the instruction sheet. ( pictures are upside down) Install drain on pump. Remove wirng connectors(3) and hanger. Raemove in/out pump clamps, and remove pump. Reverse procedure( I had to bend the new hanger to fit). When I first fired it up, nothing happened for about 5 min. Then water got into the pump and it started working. Quieter, more powerful spray. Grabbed a beer.

Instead of purchasing a new dishwasher, I elected to replace the motor/pump assembly which the existing was noisy and leaking water. To start to took pictures of the existing assembly and marked the wiring connections. I read the instructions a few times until I fully understood and had the necessary parts identified. The only problem was the bracket that holds the solenoid has two holes for mounting the drain feedback bracket were not threaded. I was able to tap the holes (metric) and mount the bracket. Caution must taken not damage the solenoid coil.

Too easy- what made it easier was this is a portable roll-around unit I could lay on it's back. Loosen the two clamps around the washer pump, hook up the drain solenoid, washer motor wires, attach the motor hanger, that's basically it. It took longer to make sure I was working from the right set of instructions- this pump covers several models. Once I had that right, it was really a snap. Now the unit is so quiet. It once sounded like a jet engine in the kitchen, now it runs so quiet you can hear the water splashing around inside- a big improvement. We should be able to hang onto this thing for a while longer.

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

Removed old gasket. Then cleaned the track with a strong paper towel soaked in Windex to remove accumulated scale/soap. Followed the instructions provided with the gasket. I did not need to remove any screws from the door nor did I need to tumble the gasket in a dryer to remove kinks (There really were no kinks in the gasket, as supplied.). I did use a mirror to locate where the gasket should go underneath the bottom of the door, which you can't see. Feeling for the track with your fingers was sufficient for the installation.

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!

followed the excellent instructions accompanying the gasket.

Removed old gasket, cleaned grooves, installed new gasket

Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!

This was really easy. The parts fit perfectly. First i turn off power at circuit panel; turn off water and dissconnected water line and discharge hose. Removed dishwasher from under counter and placed on side. Disconnected connections to motor and pump and replaced and installed same as one unit.