Models > 36291201003 > Instructions

36291201003 Kenmore Range - Instructions

All Instructions for the 36291201003
31 - 45 of 166
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
nylon guide was broke off
took drawer out removed broken guide. It had 1 screw removed it put the new guide in place put screw back in. Put drawer back in stove, It works fine.
Parts Used:
Drawer Glider - Right Side
  • Lathan from Goodyear, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The element split open and burned out
I unscrewed two screws inside the over over the element. Then I slowly pulled the element out and unplugged the two wires attached. Afterward I pushed the element back in place and screwed it back in and was done. Sure saved $550 I thought I might have to spend on a new oven,
Parts Used:
Bake Element
  • Thomas from Houston, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The bake element quit working.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the wires to the new element and reinstalled the two screws. A brief test showed the element worked and that was it.
Parts Used:
Bake Element
  • Wiley from Port Orchard, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old blackened oven racks
Replaced old with new.
Parts Used:
Oven Rack
  • Roger from Falls Church, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
8 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner shorted out
Pulled burner out of socket and pushed new burner into socket. Took less than a minute.
Parts Used:
8-Inch Surface Element
  • Richard from Waynesboro, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no burnt wire
Replace part an wires
Parts Used:
Power Terminal Block Kit
  • Bernard from N CHARLESTON, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
every thing went great
every thing went great
Parts Used:
Bake Element
  • CLYDE from SAINT PETERSBURG, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
terminal was broken due to maney uses
unscrew the terminal block,pulled the old wires out,installed the new wires installed the new block
Parts Used:
Surface Burner Terminal Block Kit
  • Emmett J from Winchester, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drawer glide broken
took nut driver to remove the old and replaced with new. simple.
Parts Used:
Drawer Glider - Right Side
  • TERESA from SALTVILLE, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
none
slid the old ones out and slid the new ones in. done
Parts Used:
Oven Rack
  • Michael from Laughlin, NV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the old element bunt out.
Followed the video and it was fast and quick.
Parts Used:
Bake Element
  • Sandy from PALMER, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two sockets for electric elements and their end terminals were badly burned.
0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!

That's it! It took about 20-30 minutes.
Parts Used:
Surface Burner Terminal Block Kit
  • Marco from Santa Barbara, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The burner bowls were burnt through and nasty looking.
I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Isabel from The Colony, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
a pan was dropped on hot bake element,,bake element broke
i dd not notice at first and started the self cleaner,,,i notice the self cleaner did not work,the screws had to be sprayed with dw30a couple of times and a pair of pliers to remove screws(no wrench set)after removing screws pulled the wires out to see and removed the connection to wires,,,replaced with new bake element and replaced the screws works fine,,,by the way i am a 64 years old grandmother
Parts Used:
Bake Element
  • fran from harrisburg, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven coil burned out
Removed the hexagon screws. pulled the unit out and wiggled the tabs loose disconnecting them. Installed the new unit-attaching the tabs making sure they were tight. Put the new unit through the opening in the back of the oven and reattached the hexagon screws. Back in business in about 10 minutes.
Parts Used:
Bake Element
  • Nancy from RUSH, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 36291201003
31 - 45 of 166
Back to Top