36291112004 Kenmore Range - Instructions

GAIL from STREAMWOOD, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner not heating

Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.

Parts Used:

Surface Burner Terminal Block Kit

Henry from Norwich, CT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

stained drip bowls

unplugged burners replaced drip bowls plugged in burners

Parts Used:

Sunny from Salt Lake City, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Bake Element burnt out

watched the video on part select - took less time then they said.

Parts Used:

Greg from Chicopee, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

Was this instruction helpful to you?

old,burned pans

replaced

Parts Used:

James from Apache Junction, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Broiler Element Replacement

There were two small screws at the back of the stove (this was the part that intimidated me. At first glance it doesn't look like it should be removed). But you just have to unscrew them, disconnect the wires behind them (this part can be done by hand), and pull the element out. The new element slides right in! Just make sure the power to the stove is disconnected either by breaker or by unplugging it. I'm not sure if it matters, but I made sure to connect the wires to the same side of the element that they were removed from.

Parts Used:

BROIL ELEMENT

Emily from Snoqualmie Pass, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Heating element not working

Saw the brief video and as stated took less than five minutes to replace. It took longer to clean up the floor under the oven than to replace heating element.

Parts Used:

Stuart from Yelm, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

burned out

replaced

Parts Used:

mary from morton, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

the bottom element of the oven was broken

attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!

Parts Used:

DAVID from PARIS, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

heating element blew apart

I watched the video on this website and it couldn't have been easier. The only thing I did differently was I took the door off for an easier reach. To take the door off, you open just a little and pull up. It makes it so much easier to get at the screws, and maked the repair a snap.

Parts Used:

Lori from Bellows Falls, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Plastic glide broke

The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.

Parts Used:

Drawer Glider - Left Side

Mary Ann from Granby, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

My drip bowls were rusted and corroded

I ordered new drip bowls and put them in place. They fit just fine.

Parts Used:

Glenda L from Lake Placid, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

needed new drip bowls for stovetop GE

removed the burners and dropped the drip bowls in. Very easy to do,

Parts Used:

Patricia from Centereach, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

GE Electric Range rear left burner quit coming on

Removed the back top cover with 1/4" nutdriver. Removed the burner terminal block with 1/4" nutdriver. Within 15 minutes had the terminal block kit removed and installed and in service.

Parts Used:

Surface Burner Terminal Block Kit

Richard from Richmond, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Needed to replace drip bowls

Husband just snapped in place in about 8 seconds! Thanks for the fast delivery and pleasant staff assistant.

Parts Used: