3542XRW Magic Chef Range - Instructions

All I had to do was pull the drawer out and screw on the new part! Awesome experience...and it was so easy to find the part on the website, everything is very clear and with pictures to ensure where the part belongs...who could ask for more?

Very simple fix--unpugged two fittings in the back of oven plugged in the new element and it was done.The Best part was that the element burned out on a Sunday and I ordered the part that day and it shipped on Monday and received part on Wed AM.This is the second time I've had to replace the element and by ordering through Part Select I saved $24.00 versus buying it from an appliance store.

Don Samuelson

Ordered element and recieved in two days(yea). Removed back cover from unit. Removed two wire slide on wire clips. Then went inside oven cavity and removed two screws holding element intact. The element slid out. Installed element, re-installed two screws to hold element intact. Attached wire clips back on to element, re-attached back cover. Plugged unit back in and it worked perfectly. Eazy-peezy lemon squeezy.

John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600

Turned off power circuit to oven. Removed old element by unscrewing two nuts attaching unit to back of oven. Used pliers to help release electrical connections at both ends of element. Re-attached connections to new unit. Screwed nuts back into place. Turned power back on and cooked dinner. Total time for repair was less than 5 minutes.

Was glad to get the correct ones for a 30 year old stove. Had already wasted $12 shipping trying to order from someone else.

This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

I Unscrewed the attachment plates located at the back of the over. Pulled the element out so that I could "unhook" the prongs. Replaced the new element by clipping on the prong attachement (you will see where the electrical wires are). Screwed the plates back on and Vola! I'm baking again.

Pulled out the old burners and put in the new ones.

I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.

My husband removed the screws holding the damaged element and removed it before the new one arrived. When we received the replacement part, it took only about 10 minutes for him to repair the oven, inserting the new element.

My wife detected the problem Wednesday evening before Thanksgiving. We've had the heating element break before, so we knew right away what the problem was. We ordered the part that night, and even though we weren't able to cook Tom for Thanksgiving, the part shipped on Friday and arrived the next Thursday.

First, I turned off the power to the stove at the circuit breaker.

Then, I removed the two screws that hold the element in place. They are on the top of the flange and partially concealed by the convection element that juts out.

I pulled out the heating element, disconnected the electrical leads, and installed the new one.

I attempted to put the screws back in, but they were a little tough to line up. I decided to leave them out, knowing that I will probably be doing this repair again in a couple of years.

Hopefully, next time it won't be the day before Thanksgiving.

i read the installation instructions and followed them. first i made sure that each heating element was off. next i carefully removed each one (a total of 4) from it's plug and lifted the worn out drip-bowl up and replaced it with the new one. finally i pluged in (a total of 4) heating elements and turned them on to make sure them were working and they did.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

Rehooked up wires on new element, Slid the element in place. Replaced the two screws. Done, very easy.

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan