3527XRW Magic Chef Range - Instructions

removed drawer from track replaced supports on track and one on the drawer.

the new elements were super easy to replace. the old ones just pulled out and the new ones easily pushed in. the top one was a little more difficult only because it had brackets that had to be slid of and then slid onto the new one.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Pretty simple, except the element melted very close to one end, so the screw holding the element to the rear of the stove was partly melted also. Had to drill it out & used a nut & bolt to secure the new element.
Apart from that, it was a breeze. As others have done, I re-tightened the lugs that the element plugged into.
Suggest a "test heating" before using stove: mine had a strong odor on first use, fine afterwards

Unplugged stove. Removed door. Unfastened 2 screws at rear of oven. Removed wires from bake element. Connected new bake element. Replaced screws and door. Plugged oven back in.

Unscrewed two screws holding element in place and pulled off the electrical wires to the element.( be sure to remove power to the stove)Put wires on new element and installed screws back in. Done

Shut off electricity to appliance then unpluged wiring from old element and pluged in new element.

Removed 2 screws, should have tripped breaker first but learned the hard way, unplug wires, install new.

Turned off the breaker to the stove. Removed the screws holding the old parts in and unplugged the element. After reshaping the element because it got damaged in shipping I plugged the wires to the new element, replaced the screws and turned the breaker back on. Tried the stove and it has worked fine since.

Two screws out, the old bake element came out easily, was able to disconnect very easily from the clip wiring, then replaced with new. I even was able to replace the oven light bulb at the same time. A real cinch.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, at that point I attempted to reconnect the two wires, that is when I found out why they tell you to unplug the electricity. It wasn't a big shock, more of a consistant shock. Once I unpluged the stove from the wall, it only took about 3 minutes or so to connect the wires and replace the two screws. I have no doubt I saved a hundred dollars doing this myself.
Thank you for your prompt delivery on the replacement part for my Bake Element at what I felt was a very reasonable price.

Removed back of stove (6 screws), puled clips loose. Two screws inside oven, pulled out old element. slid new one in, replaced screws, slid on clips replaced back panel. Don't forget to unplug the stove frist.

Took out 2 screws pulled off the 2 female connectors. put the conectors on the new element and put the screws in. It took less than 10 minutes

This was a snap. It took me longer to find the right part number than it did to make the repair. After securing power to the oven, I removed the racks. I then unscrewed the element supports and pulled the element out slightly to expose the connectors. Using a pliers I removed the connector from each side of the element. At this point, I should have placed a piece of electrical tape to prevent the connector leads from slipping back into the body of the oven. Instead, I fished them out with a tweezer, and slid the connectors back onto each side of the element. I then screwed in the elements supports, replaced the oven racks, and restored the power. It literally took less than 10 minutes.