3147XTW Magic Chef Range - Instructions

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

1) removed 2 lines 2) removed 4 screws 3)pulled out old element4) relaced new part 5)installed screws 6) install lines &tighten

First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.

Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.

first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.

I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.

I didn't. Don't know how to get to light bulb to change it for this specific model

ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job

1. Screw the burners counterclockwise 45 degrees to remove each burner. Some gave easily while others were baked on.
2. Remove one philips-head screw per burner.
3. disconnect ignition wire from each burner.
4. remove stovetop.
5. remove the previous hammered orifice and tube assembly by unscrewing 4 nuts.
6. attach the new assembly and follow steps 1-4 in reverse order.

The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to fully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!

First I removed the two screws that held the element in place. I removed the old element and placed the new part in place, then replaced the screws.

TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN

Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.

The old burner head had corroded allowing gas to come out at the bottom. The actual replacement is just turning the head, lifting it out, transferring two wires with slip-on connectors from the old burner to the new one, and dropping the new one in place. Most of the time was spent sanding away corroded metal on the base to make a good fit. The information on the burner head says that the company has decided not to use a gasket under the head. I suggest that was a bad decision.

Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel  tool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!

Barry