3121WTA Magic Chef Range - Instructions

open oven door remove bottom tray pull off two screws unplug wire remove old part install new part

remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.

Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason it did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!

During removal of the original ignitor the screws would not come out. they were rusted. using some liquid wrenchI tried to remove them again and they broke. Using an angle drill and special bits I was able to drill out the screws. I re- tapped the holes and the repair was simple. My wiring required additional insulation over the supplied wiring that came with the new ignitor. Cut the wires about 1 1/2 inches from the plug and added the insulation then replaced the plug with the provided wire nuts. Mounted the new unit and all tested perfectly. Closed up oven and operates perfect as if new.

My oven would no longer ignite, and I asked a friend to help me see if we could fix it. We found an appliance repair manual online (www.appliancerepair.net), and it described that the most likely part needing replacement was the ceramic igniter - they do wear out, and my oven was - after all - over 20 yrs old, with never a repair! Then, somehow I found this PartSelect website, and after entering the make and model number, it showed the part, with a drawing, and dimensions - enough for me to be convinced it was the right part. I called and was reassured that if it were not the right part, it would be easy to return / refund. So, I ordered the part, standard shipping .... and to my great surprise, it was delivered the VERY NEXT DAY to my front door! And this was right before Christmas, a very busy time! The oven works like a charm now..... (I also had to clean out some of the gas holes, which can build up residues over time.) This repair cost less than $50, I'm sure if an appliance repair person came out it would have been more like $200 - not worth it for an oven this old. So, I'm happy with PartSelect!

Fist I removed the screws on the front-sides of the oven. Then I turned off the gas, by adjusting the in-line valve. I then unscrewed the gas fitting going into the bottom of the oven. I pulled the oven out, being careful not to put too much pull on the electrical cord. I put a bench in front of the oven and set it down.
I then removed the oven racks, and the plate in the bottom. Bottom element is bake, top element is broil. I unscrewed the igniter, then disconnected its plastic wire connector on the back of the oven, then pushed and pulled the connector into the oven and out the door.
Then I ordered my part for $30 less than Sears from PartSelect, and it got here STUPID FAST. I hooked it up and put everything back together, no big deal, BOOM - Cornbread!

removed door (pull up and out), removed all racks and bottom of oven, removed two screws holding old igniter, unplugged old igniter from harness, mounted new igniter using two screws and nuts purchased from local hardware store, plugged new igniter into harness, replaced bottom of oven and trays, slid oven door down over hinges. Oven works properly. Thanx!

I am a novice at this, so before I did anything I researched this site and made sure to read the installation directions that came with the part.

First I removed the oven racks, the bottom cover (one screw in front and two back latches by moving them towards me) and the fire cover underneath that. Next I disconnected the electrical plug in the back.
Then I removed the defective part by unscrewing 2 back panel screws and 1 on the side of the igniter itself. Now, in connecting the new igniter I cut the connector off of the old one and wire nut connected it to the new one. I did check the connectors and cleaned them by simply plugging/ unplugging them a few times.
Next, The trickiest thing about installing the new igniter was pushing the wires all the way to the back of the oven. I took care and time in this to insure that the connection was well insulated from the heat and then plugged the hole with the insulation material supplied. Next I recconected the fire cover and turned it on. Worked great! Put everything back together, plugged it in and Voila! Like new.

unplugged the oven, unplugged the ignitor and removed the two screws

Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

snaped them into oven cavity attached temp bulb job complete

Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.

was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!

2 screws easy to remove and plug in the wire. job done.