3101WPW Magic Chef Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would not start, ignitor was not doing anything
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up and then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
Parts Used:
-
Michael from Syracuse, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The burners were old and loose
First, I raised the top. Extracted the holding pin, Then replaced the burner. Then reinserted the holding pin. Two minutes top's.
Parts Used:
-
James R. from Corona, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broke the igniter in the oven before I even got the oven installed
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Parts Used:
-
june from wills point, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven igniter came on but the gas valve never turned on.
1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS
Parts Used:
-
James from PEORIA, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven taking to long to preheat.
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Parts Used:
-
Isaac from LATHRUP VLG, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Parts Used:
-
Tara from ALBANY, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
my knobs were broken on 30 year old range
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.
Parts Used:
-
Larry from LAWTON, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced upper over light and assembly
I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light assembly from the front of the oven and had to go in from the back.
Parts Used:
-
Thomas from SAN DIEGO, CA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Racks were old
-
Sandra M from DISTRICT HTS, MD
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
1960's oven door gasket fell apart, actual gasket not available any more
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Parts Used:
-
Mary from WINCHESTER, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Parts Used:
-
Anita from ELKTON, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Parts Used:
-
Mz from COLUMBIA, ME
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original rack had melted plastic on it.
-
Linda from BURBANK, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas would come on, would not ignite. Oven not heating.
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Parts Used:
-
Karen from DAYTON, OH
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven igniter would glow red but gas did not come on to light the burner.
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Parts Used:
-
Ernest from CINCINNATI, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!