3100 - Instructions

First I removed the oven door by pulling straight up off of the hinges in the open postion. Next remove oven racks,then use 1/4 nutdriver to remove back screws on inside oven bottom plate. Next remove gold nut on silver tube @ pilot connection,then remove 1/4 nuts that hold pilot assembly. Next open top of stove and remove small gold nut "with the thin wire from pilot"attached to the back left of oven control knob. Snake that nut and wire from the top of the stove down to the oven and removethe whole pilot assembly. To install carefully unroll the new pilot assembly starting from the oven "there are two round holes you need to snake the tube into"and up behind the back & into the stove top. Make your connection@ the oven assembly. Next attach the assembly with the 1/4 screws that you removed,then make your connection"gold screw silver tube" now push in your oven control knob to alllow gas to flow to the pilot tube and check for leaks with a water @ soap solution. No bubbles no leaks. Light your pilot . . . . You must hold in the oven knob. Put back in oven plate,,,, 1/4 screws,,,,racks close the stove top ,put door back on hinges and your done. . . . . Hope I helped,. . Pete

First I removed the oven grates and then the metal plate that covers the burner and igniter.Then I removed the two screws that hold in the igniter,be careful because the threads on the sheet metal screw strip off easily due to the heat. Then I slid out the storage drawer on the bottom of the stove.Next I removed two screws that hold on a cover in front of the gas valve where the igniter is plugged in.I unplugged the old igniter, removed it then replaced it with the new one.I then reassembled everything in the reverse order.I did have to use a nut and bolt to replace the damaged sheet metal screw.

First I removed the oven door for easier access then, removed the oven grates and bottom pan. Then there is a wing nut that holds the heat deflector in place over the manifold thats needs to be removed. Now you can see the igniter, remove the 2 small hex head screws and disconnect electrical connection.
Simply reverse the sequence to reinstall.
This may sound like alot to do but it only took 15 minutes to complete and I'm not an appliance repair person. Anyone who is somewhat of a handyman can accomplish this job.

i need to replace the lower oven igniter about 2-3 years
unplug the oven
open the oven door half way then slide the door up
take out both racks
push the bottom pan away from you and lift up
one screw holds the igniter on
pull the wire out until you get to the electrical plug
disconnect

I am a retired lp Gas service person so this was quite
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.

Turned gas and electricity off first. Pulled out the bottom pan so I could access the igniter. Removed two screws holding the igniter next to the burner tube, unplugged the igniter from the back of the stove and then pulled the plug threw into the oven. Mounted new igniter and then pulled the plug threw and plugged it back in. Reinstalled bottom pan and I was done in 15 - 20 minutes. VERY EASY TO DO...

Pulled the stove out from the wall. Removed the left side of the stove. Removed the wires from the old igniter. Modified four of the wire ends with the proper size spade connectors (supplied with the new part). Reinstalled the wires onto the new part. Tested the burners. Reinstalled the stove side. Moved the stove back into position.

Step1: Remove oven door. Open oven door about 3-4 inches and pull up with 2 hands.

Step2: Turn oven light ON so you can see.

Step3: Remove bottom tray by pulling on the 2 rear clips and lift tray up and out of the oven.

Step4: Using a nut driver remove the 2 nuts holding the ignitor in place. If nuts are rusted from heat spray a tiny bit of WD-40 on them and totally wipe off any excess when finished removing the nuts.

Step5:Pull wire from old ignitor through the insulation and unplug it from its connection.

Step6: Plug in new ignitor and push it back through the insulation and fasten it back in position with the 2 nuts.

Step7: Re-install bottom tray and door and CONGRATULATIONS cause you just saved yourself about $150! by DIY And you never again will be eating semi-raw chicken or better yet, take the money you just saved and treat yourself and your family to a sushi dinner.

I would like to thank Partselect.com for their quick delivery and very reasonable price on the Ignitor I purchased.

Regards.

first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you

Pulled off the oven door, just lift straight up. Pulled out the floor of the oven, very easy just lift from the back. The only problem I had was the screws holding the old igniter wouldn't come out, they just spun. I snipped them off and picked up two new ones at the hardware store. Pull the wiring harness in through the hole in the back of the oven. Unsnap old wiring harness, snap in new one. Reattach the new igniter, replace floor, replace door. Turn on oven and cook food... fairly easy repair.

Removed (4) screws that hold the orfice assemblies in place. Removed the 4 nuts from the gas feed tubes. Placed the two new orfices in place and attached the nuts. Replaced range top and replaced the (4) screws into the orfice assemblies. Done. Worked fine the first time.

I first removed the bottom of the oven and the flame guide to uncover the igniter assembly. Then I applied WD40 to the two Philip head screws and unscrewed them to release the old igniter. The two wire leads from the igniter went into the back of the oven and I could not reach the connection block. So I pulled the oven out far enough to get behind it and took off the panel covering the electrical wires in back. I had previously disconnected the electrical cord from the wall outlet. After I determined that I could not remove the connection block I returned to the igniter and cut the two existing wires close to the ceramic igniter assembly. I marked the top wire with a Sharpie pen so that I would not mix up the new leads when I install the new igniter. Although it was awkward to work inside the small oven space I was able to strip the insulation back about 1/2 inch and then connect the new igniter wires using the twist caps supplied with the kit. I pushed the wires back into the space and added the insulating material supplied. The igniter assembly was then installed with the original two screws and the other oven covers and flame guide reinstalled easily. After reconnecting the power outlet the oven was back in operation with ignition of gas flame within a minute or so. It was a good feeling and now we do not need to consider replacing the gas range.

Take a few screws off the back of the slide in burner module. Take off the back. Unscrew the ignitor screw, remove ignitor carefully, replace with the new ignitor, put the screw back in, put the back back on, try it out! Ours worked after a couple of tries - don't know if the ignitor had to "rev up" by several sparks or we just didn't have it properly installed at first. Anyway, very easy. Did it in my pajamas on a Saturday morning.

Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws holding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!

The bottom burner would not stay lit. I determined that it was as a result of the ignitor's voltage droping. The thing still glowed red but apparently the voltage drops and closes the gas valve. So, I switched the broiler one with the bottom one to see if it would work. It did. Then I bought the new ignitor and put it in where I had taken the broiler ignitor out. You have to take care to put the insulation back and shove the connector well into the hole so that there is no possibllity of it melting. I also replaced the oven top. I had bought that part a couple of years ago because I had dropped some things on it and it was chipped. When I got the top I thought it would be somewhat intuitive as to how to replace it. But, it wasn't. So,it stayed in its box. When I had the other problem I decided to tackle the top too. First turn off the gas and unplug the oven. You have to pry the top off with a screw driver. Then, you disconnect wires which run to the ignitor for each burner. You also have to disconnect the gas lines running to each dial. Now, you take the top off. To get the burners off the top you have to take a pair of channel locks and open them wide, wrap a rag around the burner and turn them like screws. Under the top there is an assembly that holds the gas lines in place. that has to be removed from under each buner. These assemblies are not interchangeable!!! One is left and the other is right. You then reverse everything. Put the burners in by screwing them down. Its hard but if you put a rag over them you can strike them with a rubber mallet. Screw the gas line assemblies into the bottom of the top. Then hook up the wires and then the gas lines. Then, you pop the top back in. There are those pressure clamps that hold the top down. I made a mistake with the gas line assemblies and switched them. So, when I tested the repair I realized I had the front dial controlling the rear burners and vice versa. Some day I take it all apart and fix it again!