All Installation Instructions for Whirlpool Refrigerator 2VED21ZKFN03

Two bottom drawers were broken

Took out old drawers, slide new drawers in.

Parts Used:

Refrigerator Crisper Drawer With Handle

Refrigerator Crisper Pan

Mary Ellen from SPRUCE PINE, AL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator door on a side by side unit would not stay closed.

First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!

Parts Used:

Refrigerator Door Cam

John from Conyers, GA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

changed the light bulb still would not work so I figured it was the switch sure enough.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Parts Used:

Refrigerator Door Switch

anthony from HAVELOCK, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

defective light switch

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Parts Used:

Refrigerator Door Switch

THOMAS from WILLARD, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Freezer Temp was -20 to -30 degrees F. and did not defrost because of the extreme low temperatures.

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

Parts Used:

Refrigerator Bimetal Defrost Thermostat

George from ENDWELL, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

the light socket broke apart

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

Parts Used:

Light Socket Kit

Elyse from Skokie, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Broken door handle

Unscrewed old handle amd put the new one on with the screws.Took less than 5 minutes The part was a perfect match. Very easdy!

Parts Used:

Door Handle

Thomas from Blue Point, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Parts Used:

Refrigerator Door Switch

David from Hemet, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Crisper bin had broken pieces off the track edges

Bought new one and installed

Parts Used:

Refrigerator Crisper Pan

Carl from SPARKS, NV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Cracked

Else one out and the new one in

Parts Used:

Refrigerator Crisper Pan

valaida from FRANKLIN, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Drawer was damaged and would not pull out or push in.

Replaced the drawer with a new replacement.

Parts Used:

Refrigerator Crisper Pan

Edwin from BAKERSFIELD, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Crisper shelf glass missing

Removed cheese & cold cut drawer accessing lower crisper drawer glass missing from surrounding frame.
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass

Parts Used: