This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$17.95
In Stock
Order within the next 8 hrs and your part ships today!
This lid switch assembly is for a top load washer. The lid switch assembly detects if the washer lid is open or closed and prevents the washer from spinning when the lid is open.
$169.97
In Stock
Order within the next 8 hrs and your part ships today!
This suspension rod kit includes four rods that stabilize the wash tub, reducing vibrations and movement during cycles. It is compatible with a range of washing machines and helps improve performance ...
$118.13
In Stock
Order within the next 8 hrs and your part ships today!
If your washer is noisy, shaking, or leaving clothes wet, the drive block might need replacing. This part connects the basket to the drive shaft so it can spin properly during cycles. It’s built for l...
$29.65
In Stock
Order within the next 8 hrs and your part ships today!
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This po...
This shift actuator is an essential component in washing machines, responsible for switching the motor between spin and agitate modes while also communicating spin speed to the control board. A malfun...
$111.52
In Stock
Order within the next 8 hrs and your part ships today!
Struggling with a leaky washing machine? Don't despair! The Whirlpool Washer Tub Seal is here to save the day. Think of this as the secret weapon in your washer's arsenal. Nestled in the heart of your...
$85.98
In Stock
Order within the next 8 hrs and your part ships today!
Order within the next 8 hrs and your part ships today!
Questions And Answers for 2DWTW4705EW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dennis
September 5, 2021
Machine not turning on, no lights on the panel.
For model number 2DWTW4705EW1
Hello Dennis, Thank you for the question. We suggest testing the Outlet the appliance is plugged into and checking the Power Cord. If they are good, the Control Board could be defective. We hope this helps!
Hello Beverly, thank you for the question. According to our research, we are providing you with general instructions that will help you reset your washer.
1- Turn the washing machine off manually.
2- Locate the washing machine’s circuit breaker in your house’s electric panel.
3- Lift the circuit breaker. This will disconnect the power from the washing machine.
4- Wait for 3 minutes.
5- Reset the circuit breaker to bring power back to the appliance.
6- Wait 30 seconds.
7- Turn the machine on at the control panel.
We hope this helps!
Was this helpful?
Thank you for voting!
Ramone
December 18, 2024
Maschine when turn on it keep on making a click click sound when lock or open
For model number 2DWTW4705EW1
Hi Ramone, thank you for contacting us. Based on our understanding, the issue could be with the lid lock assembly, part number PS12704713. You may need to replace it to fix the issue. We hope this solves your problem!
Hello David, thank you for your question. A loud banging noise from a Whirlpool 2dwtw4705ew1 washing machine during the spin cycle is often caused by an unbalanced load or a problem with the suspension system. The suspension rod kit is PS11703288. We hope this helps.
What causes flashing lidlock light on machine and it won't do anything.
For model number 2DWTW4705EW1
Hello Terrence, thank you for contacting us. According to our research, you will need to replace the lid lock assembly, part number PS12704713, to fix the issue. We hope this information helps!
Replaced the 4 suspension rods/springs. Only disconnect and replace one at a time. The tub will fall out if you disconnect and replace more than one rod/spring at a time.
This was a learning experience but it appears to have worked out in the end. Our 3 1/2 year old washer was not agitating much and I attributed that to a loose bolt. I would tighten the bolt and it would work ok for a load or two and then stop agitating. I would find that the bolt was loose again. I took a number of steps to try to get the bolt to stay on tight - threadlock, a new bolt, more threadlock, and applying progressively more force on the bolt, with no better results. Yet the repair guys on you tube were saying the bolt only needs to be snug, not super tight - something was amiss. I even went so far as to secure the basket with a rope so I could use two hands on the socket wrench (please don't do this). But when I tried the washer again there was no agitation at all! I observed the agitation output in manual test mode and the bolt was turning in lock step with the shaft but the agitator wasn't turning at all. That's when I suspected that the problem was actually a worn lower agitator. Trouble was that now I couldn't seem to get the bolt off. Turning the wrench caused the shaft itself to rotate so I couldn't loosen the bolt from the shaft. I thought I broke the washer. Then I considered that maybe the shaft was rotating because the washer was in an agitation mode when I turned it off. I went back into manual test mode, made the washer spin, then turned it off. Fortunately, this worked. The shaft was again stationary and, albeit with great difficulty, I got the bolt off.
I removed the agitator, and as a pro would have figured out long before, the ridges inside the top of the lower agitator were almost completely worn down. I realized then that the contact between these ridges and the splines on the shaft is what is supposed to cause the lower agitator to move with the shaft. The purpose of the bolt is just to keep the agitator in the correct position and from coming off the shaft. I had been trying to compensate for the worn agitator ridges by over-tightening the bolt, creating some contact at the top of the shaft. This would work for a little while, then the agitator would start slipping, and the slipping agitator was acting just like a wrench loosening the bolt (until my stupid rope trick, that is.)
So I ordered a new agitator (only the lower agitator was bad, but the price of an entire agitator isn't a lot more than just the lower part and I was reading that the upper agitator parts will wear over time) and another new bolt (because my repeated attempts to over-tighten the first one I ordered had split the rubber gasket apart and worn the bolt head).
The new agitator fit snugly on the splines of the shaft so I sensed no need to use excessive force on the bolt. Just an easy one-handed snug tightening with the socket wrench, using the other hand to hold the lower agitator. The washer is now working again.
