2538389762 Kenmore Refrigerator - Instructions

loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws

Ordered ice maker, watch video of how to. It takes less than 5 min. Installes just like the video. Loosen 2 1/4" Screws, lift ice maker up, unplug old unit, Reverse. Just make sure water tube is lined up when you install new unit and wire is tucked up out of the way. Mine did not really start making ice till the next day.

It was very simple, used a nut driver to loosen the attachment nuts that held the ice maker in place. Disconnected the wiring harness. Removed the leveling tab from old ice maker and attached it to the new one. Then reassembled in the reverse order. As they say it was no brainer! The best part of the repair, was hearing the ice dump.

I loosened the 2 1/4 inch nuts with a nut driver, disconnected the wire harness, and removed the old unit. to replace, I simply connected the harness and bolted the unit back in. The job took about 10 to 15 minutes and the new unit works better than the old one ever did.

Removed 2 screws that hold ice maker in place. Unplugged and took out of freezer. Used the screws I took out to put new ice maker in. Plugged in the power and in 2 days I had a full ice bin and haven't had any worries since. Should have replaced the broken one along time ago but thought that the process was harder than this. Very easy and suggest this to anyone having ice maker issues. Less than $100 and never have to buy ice for the house again.

Followed the instructions that came with replacement ice maker...was very clear and easy to follow and only took 5 minutes. I also watched the video sent via email with my order confirmation which was very well done and easy to follow. The only information that would have helped would have been a note to wait over-night for the ice maker to make ice as I thought I did something wrong when it wasn't making ice right away....waited until morning and had lots of ice. If I knew how straight forward and easy this was, I would have done it a lot sooner.

I found that the fill solenoid for the ice maker was down to a drip when energized. I ordered from this site and replaced. now plenty of water, but the ice maker would just stall and jump teeth. The heater which heats the ice up to free it from the mold was defective. Ordered from this site, and now working great.this sitet has good pricing, and the help illustration is great, and explains the sequence of events. This made it easy to troubleshoot. This refrigerator has not give a problem in over 11 years. The problem is "the ice maker". I have replaced it 6 times.

Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.

Followed on line video. Also water supply tube on fridge was full of ice. You can pull it out and run hot water on it to clear.

After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!

Turned off water, unplugged refrigerator, Removed defective unit with support bracket. Installed support bracket, adjusted flow screw per instructions, plugged in wiring with adapter, hung on screws, tighened screws, secured excess wiring harness (making sure it did not hang below icemaker per instuctions), turned on water, plugged in refrigerator. Comment it took a few hours to start making ice, air in line? After a couple of days seems to be working fine.

Loosened 2 screws, lifted icemaker brackets off of loosened retaining screws, unplugged electrical connector from the icemaker.
plugged in the supplied jumper harness & connected to the new icemaker, hung it on the loosened screws, secured the 2 screws.
Dranke beer & listened to my new icemaker rock & roll.
No further problems, Frigie like new.
The price was the cheapest I could find. $78.00 total including shipping.
A little girl could replace this unit.

LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!

It was just a simple replacement, three nuts to loosen , a slight adjustment on the timer and reversal installation...As simple as replacing a light bulb! You needn't be a brain surgeon to do this job! Your installation video was very helpful....Thank you PartSelect Chuck McCann

The repair took only 5 minutes. I removed the ice bin, which just slides out, then loosened 2 screws at the back-top of the ice maker. I then unplugged the broken ice maker, removed it, put in the new one, re-tightened the screws and plugged it in. It was making ice within an hour.