2537041341A Kenmore Refrigerator - Instructions

Watched the video and read some comments and from that it was easy

took the back off refridgerator, disconnected water valve assembly, then disconnected water lines and electrcal connectors. also i received the part in less than 24 hours

removal of the old valve to identify the problem took the most time. Once the new valve came it it was easy. NOTE: the old one had threaded connectors, and the new one is press/fit so the ends of the tubing need to be cut. The color coding and size matching are great.

i only ordered 1, so i replaced each 1 then moved to the next. still no light, so it must be someting else. will try to check the wires with a volt meter to see if i have power next. something wierd happen, when i accidently touch the back of the led board, it lit up, small but still light up. hoping that means the led board is goo, must be in the wiring. i saw it had a main led board so will check the power to that.

Removed lower cardboard cover, shut off water supply valve, unpluged frig. Used wrench to remove 3/8 water line from water valve, removed electrical connectors from solenoids, used fingers to unscrew water connections from valve.

I had a repair man do the work.
That's always best.There was one day delivery on the part and the price was great. Thanks

turned off water supply, removed cardboard back, removed supply line, unhooked all color coded connections,took out bad water valve and replaced with new one note: the new valve came with pex connections so i carefully cut off flared tubing ends with sharp razor knife making sure when i pushed tubing into new valve that i did so with some force until i HEARD and felt them snap in place very simple plus i received the new valve in 2 days very happy with PartsSelect.com you CAN do it

Turned off water supply disconnected hose from valve removed cardboard backing removed the screws holding valve ass'y disconnected the three wire connections disconnected five hoses then cut and installed in new valve per instructions provided reconnected three wires reinstalled valve ass'y turned water supply back on and checked for leaks by engageing filtered drinking water in the refrigerator door replaced backing to complete job.

remove back cardboard panel, cut off water supply, remove screws holding valve to back of refrigerator, unscrew water lines & reattach to same fittings on new valve, screw new valve in place, replace cardboard cover.

Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

This was probably the easiest repair I have done on this refrigerator. I pulled the unit away from the wall, turned off the water, and disconnected the hose. I have a wooden floor in my kitchen so I was careful to put a towel under the hose and valve. Very little water drained out but I kept the towel there for insurance. After removing the access panel, I removed the two screws holding the valve in place, slid it back to where I could unplug the wiring connected to it. The connectors are color coded so there is no worry about putting them back incorrectly. The new valve uses push-in type water connections, so you have to cut the old style connections off of the plastic water lines. Kitchen shears did this easily. Then is was just a matter of pushing each line into the proper connector on the valve, reattach the electrical connectors, and slide the valve back in place. Reinstall the screws, reinstall the access panel, hook up the water hose, slide the unit back into it's niche, and run about a gallon of water through the dispenser and you are done.

The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks