25361762012 Kenmore Refrigerator - Instructions

I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.

The repair was very easy just popped the new one in place.

Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.

I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!

The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.

replaced it

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

I had to tap the screw holes with a 8/32 tap so that the screws would not bind.

My unit was not defrosting. Defrost heater was not functioning. Defrost heater tested good with a meter. Thermostat (cold) tested bad with a meter. Defrost timer was working properly. I replaced the thermostat but I had to buy red crimp connectors because the blue ones that came with the thermostat are designed for wire bigger than 18 AWG wire. The thermostat leads as well as the wire in my unit were 18 AWG. The crimp was not tight enough for my liking with the blue butt connectors. I also purchased smaller heat shrink tubing. After replacement, the defrost heater started working. I could see it glowing. Unfortunately immediately after getting the heater working the contacts in the defrost timer arced and stuck together thus preventing the timer from exiting defrost mode. The heater went off at this point indicating that the thermostat was now working. I then purchased and replaced the defrost timer and now the fridge is functioning properly. I noticed both replacement parts, even though I looked up my fridge model, were different part numbers than the originals. I'm guessing the new parts are improved? I also noticed the timer was an 8/30 rather than a 10/30 like the original. The fridge is working better than when it was new so evidently defrosting every 8 as opposed to every 10 hours is better for my unit.

Long story short:

Buy the correct crimp/butt connectors before beginning replacement of the thermostat and proactively replace the defrost timer since it is rather inexpensive.

The freezer was still making ice, but the fridge portion was barely cooler than room temp. I came to the website and saw that the defrost thermostat cured this problem over half the time. I was quite dubious because I don't see how that would affect the non-freezer part of the compartment, but since it was a cheap and easy-looking repair, I figured what the heck, lets see if that's it. Sure enough, it's like new again. I still don't understand it, but I'll take it. The repair itself is simple, just cutting out the old switch and splicing in the new. Two wires, and clip it to the copper tubing where the old one was. The switch is accessed easily after taking out four screws in the back of the freezer compartment. The only hard part was removing the ice-maker, and that's just because the two screws that hold it in are a little hard to get a good grip on. Alas, you have to get the ice-maker out to pull out the back panel, so there's nothing for it but to wheedle those screws out.

Replaced thermo-fuse

remove food, then the shelf, then use a hot air gun to defrost and loosen the back panel, then remove the panel, then defrost the coil and thermostat area. using wire tools, replaced the defrost thermostat,and re-assembled freezwr and test

per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section

My husband watched the video on your website and found it very easy to do the repair. The repair company that diagnosed the problem wanted $210 to do it. The part I ordered was under $20, and after he installed it the refrigerator has been working great. We would highly recommend your site to anyone who needs to fix anything!

I went online to a you-tube video to assess the problem and watch the repair. Ordered the part on sunday before christmas and had it christmas eve! Easy 10 minute repair. Four screws held the cover on. Two screws held the timer. Unplugged the old timer an replaced. Put all the screws back and . . . . Done! Easiest repair I've ever done. Parts select did a great job, good price, very fast service! One happy customer!