25360721006 Kenmore Refrigerator - Instructions

removed freezer door and installed the new one. This was a pretty easy thing to do, although putting the old handle on the new door was a challenge. No knowing that there is a plastic piece holding the top of the handle i broke the that piece and had to order another one. Mean while the freezer was making alot of frost inside, so that had to be cleaned after the new part came.

Removed the back panel in freezer compartment with the nut-driver. Then I cut off old thermostat connections, and spliced in new thermostat connections (repairman had already replaced defrost timer, and said not to trust connectors included on wires-they failed often). Then I snapped thermostat itself onto cooler coil. So far so good, fridge is running at 35-40 degrees a week later. Thanks Parts-Select!!!

First unplug freezer, then disconnected wires from timer.
Removed 2 screws from bracket holding time to freezer.
Attached New part with screws. .The mounting bracket is now part of New time. Reattach wires.
I let coils defrost and then plugged it.

We are not handy, we had an appliance repair person install the gasket.

I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator

The old defrost timer started making a screeching noise (probably bearings going out). The replacement part was a cinch to install. When I initially spoke to a PartsSelect person, they said the part number I gave them was not consistent with my old '94 Tappan Freezer. They were able to still find the proper replacement part number. The video that was on-line helpful also.

Use the rubber brushing to fill the gap.

Loosened the screws all around the door. easier if you take the door off the unit and lay it on a table. Cover the table with a blanket to protect the door finish. Old gasket just pulls loose. Press the raised bead on the new gasket under the plastic strip. Corners were the most difficult. Retighten the the screws and rehang the door. It took some practice to get the bead under the plastic strip.

This did not fix the problem. Call a repairman and he cannot come until 9/11. Food is staying frozen. Alarm sounds for awhile and then shuts off for a bit.

Bought the defrost timer based on PartSelect recommendations, installed it and no change. Apparently the old one was fine but since the refrigerator was in a flood and this part got submerged in water I kept it rather than returning it. I looked at everything closely and realized all the mechanical functions were working properly. Rarely does a condenser coil fail so I decided to look into recharging the coolant. Bought a 1/4 inch bullet valve, a 12oz. can of R-134a and a cheap resealable can adapter with hose, gauge and R22 to R-134a adapters. After a $30. investment Bingo, after one squirt the refrigerator began to cool and after 4oz. it now works better than new. I understand that PartSelect is in the business of selling only their parts but please consider that there can be other simple problems.

Removed the inside evaporator coil to do inside solder job, use torch to heat solder joints on the outside drier in order to remove it and install new drier. Soldered Heat exchanger line to drier and 1/4” copper line to compressor. Wrapped with new insulation wrap. Pulled a vacuum on system and then charged with 4.4 ounces of 134a freon. Works like a champ again!

freezer section remove ice trays ,shelves,unplug ice tray.use 1/4 nut driver remove back panel,use hair dryer thaw ice from evap coil ,unplug tstat remove install new one.plug in ice maker,put back panel back on ,ice maker and shelves plug refridgerator back in

I used the tool at Partselect that in theory allows diagnostic of the problem to be repaired. The result was that more tan 90% of the time with the introduced symptoms it had to be the thermostat. I order the part, got it quickly and installed. It did not fix the problem. So, be careful with the diagnostic tool, because it is just based on what most people buy when they have a particular problem. Videos for installation are great. If diagnosis was better, this would be fantastic. In my case there might be a different problem.

Remove All Interior Metal On Inside Of Upper Part Of Fridge, Then Remove Fan & Brackets. There Was A Total Of 6 Screws & 4 Electrical Wires That I Had To Remove To Have This Fan Ready To Replace. Then I Ordered A New Fan From This Excellent Online Appliance Part Select Ware House. And From There It Was Delivered To Pine Shadows MHC In Cottonwood, AZ Northern Arizona Largest Mobile Home Community In This Beautiful Verde Valley Desert. Where We Have Sunshine Every Day Of The Year. And I Thank You For The Prompt Response That Your Ware House Performed That Evening. From Yours Truly Jeff

First of all thanks to all who posted their stories, because those stories helped me to narrow down what could have gone wrong with my fridge. I did not know how frost-free refrigerators worked at all, reading your stories and doing some on_line research I understood the theory behind the work. My freezer was working constantly, but fridge was warm, cold air would not reach to fridge because freezer was completely frosted.
I had ordered defrost heater, defrost timer and thermostat. I was sure one of these parts was the problem.
First I used flat screwdriver to turn the timer manually untill frdge stopped running(timer is on the left bottom corner behind the black decoratve plastic under the door) . Waited about 20-30 min, checked ,freezer was still frosted. I disconnected the fridge from the wall socket and took shelves out from freezer compartment. This is where hair-dryer came in handy or you could wait till ice would melt on its own, which could take long time.Then loosend 2 screws on left wall that were holding icemaker unit half-way , unplugged the icemaker and took it out. Then took the light-bulb and cover off. Next I unscrewed and took the posts out that were holding shelves in place. Then I took remaining screws from back wall out and gently pulled back cover up then forward a little until I could see electrical connectors behind the cover and unpluged them. Back wall cover was ready to come out. I discovered thick wall of ice covering entire cooling unit. Used handy hair dryer again. When the ice melted, I saw the thermostat was busted open ( Iguess water or moisture got into the unit, then froze and ice pop-openned the cover damaging one of the connecting wires). I diconnected wires and changed the thermostat , which was very easy, just one clip holding it in place . Then plugged the fridge and checked if heating unit was working by touching it. Negative. Closed the door and let fridge run for 15 min, turn timer with screwdriver until fridge stopped working, cheked heater again- wallah it was warm and then it got really HOT! and melted all of the new frost build-up(a sign that thermostat was working). Closed the door waited another 15-20 min, fridge came-on on its own. Unplugged the fridge, pulled it forward from the wall and used sponge to drain the water from holding tray- about one half gallon of it. This is a good time to use a vacuum clener to undust the back and under the fridge. Then put everything back, in reverse order, ofcourse. Cleaned fridge and freezer compartments with warm soap and winneger solution (really good- this was a present to my wife who took our two little daughters to grandmmas and out of my way), put everything back and turned the fridge on recommended settings. Its been 5 days allready and it works great ( I used thermometr to check temperature inside the fridge and freezer). I'm thinking of returning defrost heater and timer back.Thanks PartSelect.Com, I saved lots of money. Hope this story will be helpfull to someone.Thanks for your time!