25355333602 Kenmore Refrigerator - Instructions

In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.

Replaced bottom door bin being careful not to put stress on the tabs to fit into molded area in door.

Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers.

Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle.
A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ice into the bin.

Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and note which pipe you unclipped it from. Cut the wires on the old thermostat midway between the plugs and the sensor. Using the supplied butt connectors, strip the wire ends on color matched wires (should be a dark blue or black) and crimp them together. Repeat with the other wire. Discard the white shrink wrapping. I wasn't able to get it small enough with a hair dryer or lighter. Plug the thermostat back into it's respective plugs. Clip the thermostat back onto the pipe you removed it from. Replace the back panel with the four screws. Ensure the bottom of the panel is set inside of the drip tray. Replace any shelving you removed. Plug the refrigerator back into the wall. Your done!

Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.

I removed the fan housing in the freezer section by removing all the screws. (7) There are two screws behind the vents. I did not have an ice maker to contend with so this was very easy. There is only two wires to disconnect....the ground wire and the electricity supply. Then you remove the unit from the back of the housing cover by removing two screws. Then the motor is removed from it's housing by removing 2 more screws. 1...2...3 and you're ready to reverse the procedure. I am not mechanically inclined and this was easy. Saved myself perhaps $120.00. Repair folks wanted mininum of $60.00 just to come out. Part and shipping cost me 33 bucks.OH, DON'T FORGET TO UNPLUG THE FRIDGE. :>)

No tools needed. Just had to slide the bin into place. HOWEVER, the bin has a jig-jagged style plastic groves on each side that need to be slide carefully into place. I couldn't get the orginal bin out in order to wash it. It looked easy - just slide it up and out of place, but when I did that the back, inter-locking pieces cracked off. I believe this is a terrible design and the bin should be replaced at the manufactures cost! The other bin slide in there with some elbow-grease. Good Luck!

For the ice dispenser, I read a blog that pointed me right to the solenoid that controls the linkage for the crushed /cubed ice.I first unplugged the fridge. Then removed the ice maker basket. Removed 2 ea screws from each side of the supports of the lower brackets. Then lifted the tray assy off the mounting bracket, moving the front of the bracket down you can then unhook the power/control connector.
The tray then comes right out. Once out you remove two screws that hold a plastic plate on. With this removed you can see the solenoid that actuates the linkage for the ice cube and crushed ice. You then remove 2 ea machine screws that hold the solenoid in. Remove grd. wire. and pull power wires off tabs. You can then remove the solenoid by sliding it out of the plastic retainer. With it out you install the new plunger and reassemble in the reverse order. 15 mins tops.

The main Refidgerator door, made a cluncking sound. Lube didn't help. I removed the door by removing the top screw from the plastic cover, then slide it forward, then remove the two screws that hold the hinge on and then lifting the door off, once off the lower nylon hinge bearing comes right out of the door, the plate is removed with a screw driver. Installed in reverse order and cluncking was gone. 10 mins

pulled fridge from wall, removed card board cover, unplug the fridge. turn the water off to the fridge. remove the water source from fridge first then remove 2 screws that hold the valve. then the wire plugs. hoses.. they were color coded.

we researched the internet with our symptoms and most sites said it was the thermostat. At $800+ for a new refrigerater, we decided to order the thermostat. Found schematics on the net, the thermostat was located in teh freezer compartment . Unplugged, removed food from freezer, removed the bottom shelf in freezer, and the back panel It was EASY to find. Cut 2 wires, replaced with new thermostat. DONE! The new thermostat came with new connecters.

When cleaning the coils on your refrigerator always remember rule number 1, unplug it first. I was cleaning the coils and hit the fan blade while it was moving with a brush, thus breaking off one of the fan blades. I ordered a new fan and installed it in about 15 minutes. Very easy repair.

Simply swapped out the entire icemaker, works like a charm

First I removed the contents from the door. Second, I removed the exposed bolt on the top hinge(per the manual instructions) and then I removed the plastic hinge cover. Up next was to remove the remaining two bolts from the top hinge. I should, at this point, say it is much easier to have someone help steady the door for you so it doesn't fall off the refrigerator. Now remove the door and the old nylon bearing. Replace with the new bearing and replace the door. This repair couldn't have been easier.

Repair was very easy - and to my great delight, they have replaced the old-style compression fittings with PEX push-fittings. You just clip the old compression ring and nut off the tubing and insert the tubing firmly into the fitting. SNAP! VOILA! PEX fittings are the greatest things since sliced bread. I used it to plumb my new house.