This is a replacement door bin for your refrigerator. It is made of clear plastic and is approximately 13 inches wide at its longest point, 5 inches deep, and 4 inches tall. The door bin holds items t...
This part is a replacement door gasket for your refrigerator/freezer. The gasket is made of rubber and is black in color. The gasket runs along the perimeter of the refrigerator door and is used to ke...
This dairy door, also known as a dairy bin cover, is a genuine OEM replacement part for your refrigerator. The dairy cover is a plastic part that serves as a covering to a shelf on your fridge door, t...
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
Sold individually.
This is a genuine part. The handle mounting shoulder screw (no.10 ab) is made for use with many refrigerators. The metal screw helps to fasten the handle assembly to the outer do...
This is a temperature sensing mechanism. It can sense the rise in evaporator temperature during a defrost cycle and cycles the defrost heater off after all frost is melted from the coils.
After silencing the alarm, it seemed to be running as normal without any unusual noises, but food was starting to thaw from the top shelf on down and condensation was dripping from the roof. We were able to place most of the food in 2 large ice chests and then the rest in the freezer compartments of 2 fridges we have in the house. I then turned down the temp dial to the coldest setting and let it run for an hour or so; no change.
After researching on the internet, it sounded like our symptoms could be pointing to a defrost timer issue. I pulled the freezer away from the wall, located the timer and used a large screwdriver to slowly advance it. While doing this, at one point I could hear the compressor kick in. I pushed the quick freeze button and let it run for a while. When I checked it in a few hours, the alarm light had gone out and water that I had placed inside was frozen. We took a chance and put the food we placed in the ice chests back in the freezer. Everything was fine several hours later.
I ordered a new defrost timer, it arrived in a couple of days, and replaced the old one with it in a matter of minutes by disconnecting the wire harness from the old timer, removing the 2 screws holding it onto the bracket, screwing the new timer to the bracket, reconnecting the wires harness, and done. It's been a week or so and no problems.
Unplugged unit from power source. Emptied the vegetable crisper and the removed crisper including the permanently fixed mounts on either lower wall of the unit which are retained with screws. Removed temperature control knob. Then removed interior back panel that covers cooling panel and controller. Carefully work panel loose as it is very thin and bendable metal. Note gaskets at each end of the panel and save for re-install. After working panel loose carefully find controller and pinch the mounting bracket of the controller which allows it to release from the panel. Now you may set panel out of the way and continue disassembling the controller. It has a thermal wire that is mounted to the back of the fridge wall with a screw clam. Note position and shape then remove. Remove ground and power connections noting position of each. Take new controller and attach ground and power connection. Bend thermal wire using thumb as a shaper to exacting shape of the old one and position in clamp and secure with screw. Note old controller had a Styrofoam cover and return this cover after attaching new controller to the cover panel. After this, reposition the cover panel and retain with screws but don't tighten screws all the way as you need to be able to shift panel while replacing gaskets at the ends. Place the end gaskets where they originally were and work both in until they seat. Tighten screws on the panel. Replace crisper and plug in. Good luck it fixed mine and the unit works great.
Turned freezer off at themostat and unplugged freezer. Removed 2 screws at front 2 at the back and 2 at the top. Lowered top cover and removed evaporator fan bracket (2 more screws) removed themostat capulary tube( 1 screw and bracket) then unplug fan motor. Removed motor from bracket (2 screws). Put on new fan motor then removed fan blade from old motor and put on the new motor. Remounted fan motor bracket and thermostat capulary tube. Remounted top cover, plugged freezer in the set the thermostat to 4 and freezer is working fine and doing its job. I orderedmotor on a Sunday and it was shipped on Monday and I received said part at 7:pm on Wednesday.
