All Installation Instructions for Kenmore Refrigerator 25331679103

freezer door handle broke off

Unscrewed the broken part, lined up the new door handle and screwed it on. Easy Peasy! I'm a 78 year old grandmother.

Parts Used:

Door Handle

Ann from PASADENA, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker stopped producing Ice.

After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!

Parts Used:

Replacement Ice Maker

Fred from WAPAKONETA, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

ice machine was now working correctly

watched the video (VERY helpful) and then removed the old icemaker and replaced it with the new one. Difficult only because of the small working space in the side by side freezer plus you can't see what you're doing when you tighten the screws. Working like a charm now.

Parts Used:

Replacement Ice Maker

colleen from salt lake city, UT
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set, Wrench (Adjustable)

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker stopped making ice.

It was very simple, used a nut driver to loosen the attachment nuts that held the ice maker in place. Disconnected the wiring harness. Removed the leveling tab from old ice maker and attached it to the new one. Then reassembled in the reverse order. As they say it was no brainer! The best part of the repair, was hearing the ice dump.

Parts Used:

Replacement Ice Maker

Kenneth from NEW EGYPT, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Fan motor in the freezer was not working. The freezer was still cool enough to keep the food froozen, but the refrigerator was not keeping the food cool and the liquids were getting warmer than normal.

Very easy process. Watch the YouTube video, it goes step by step for the repair. The part was $33, shipping was $6. Take your time and fix it yourself or pay $500 for a new refrigerator.

Parts Used:

Evaporator Fan Motor Kit - 120V 60Hz

Eric from SOUTH HAVEN, MN
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Freezer worked, no fridge

Removed panel over the motor in the freezer department. Removed screws holding the motor in, unplug wires. Reversed process to install motor.

Parts Used:

Evaporator Fan Motor Kit - 120V 60Hz

Adam from BERKSHIRE, NY
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Refrigerator did not cycle

Installation was fairly straight forward. The major complaint is that the problem returned 2 weeks later. I don’t know if I care to re-invest in another switch.
Now what?

Parts Used:

Cold Control Thermostat

JACOB from YOUNGSTOWN, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Didn't make ice

Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.

Parts Used:

Refrigerator Ice Maker Assembly

carey from PORTSMOUTH, VA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Shelf rack broke.

Ordered part easily with modal number ( they tell you where to find it). Received quickly and snapped paper in. They also had a video instruction. Will definitely use again!

Parts Used:

Door Rack

Nancy from SELINSGROVE, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Light not turning on when door opened

Used a flat head screwdriver to pop out the old switch, removed the contacts and placed on the new switch, popped the switch back in. Done in about 2 minutes.

Parts Used:

Light Switch

Michael from TUCSON, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Water Inlet Valve not sutting off

very easy, 1 screw, 2 tube connectors, hardest part was pulling refer. out of enclosure.

Parts Used:

Water Inlet Valve

David from SHERIDAN, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Broke door rack trying to clean it

Install by sliding the rack directly down above the fridge's tabs.

Parts Used:

Door Rack

Ty from GREEN BAY, WI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Refrigerator wasn't getting cold

removed the back panel of the freezer and unplugged the connector for the Motor. Removed the air diffuser, then removed the fan blade. Removed the 2 screws holding the motor to the bracket. Disconnected the old wire harness and installed the new one. Put the fan blade onto the new motor and installed the motor onto the bracket. Put the air diffuser back on, plugged the motor back in and fastened the back panel. Plugged the refrigerator into the outlet and tested, OK!

Parts Used:

Evaporator Fan Motor Kit - 120V 60Hz

Brad from STOCKTON, CA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Coils frozen over. Refrigerator not cooling

I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!

Parts Used: