25331447303 Kenmore Refrigerator - Instructions

removed the back panel of the freezer and unplugged the connector for the Motor. Removed the air diffuser, then removed the fan blade. Removed the 2 screws holding the motor to the bracket. Disconnected the old wire harness and installed the new one. Put the fan blade onto the new motor and installed the motor onto the bracket. Put the air diffuser back on, plugged the motor back in and fastened the back panel. Plugged the refrigerator into the outlet and tested, OK!

I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!

Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.

Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.

The repair was very easy just popped the new one in place.

I loosened the 2 1/4 inch nuts with a nut driver, disconnected the wire harness, and removed the old unit. to replace, I simply connected the harness and bolted the unit back in. The job took about 10 to 15 minutes and the new unit works better than the old one ever did.

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Ordered a new evaporator fan motor and watched the repair video supplied by part select on their web site.It was spot on step by step instructions

I just followed the instructions on the videos.

pulled back panel to get at evap fan motor cut wires to remove reinstalled hooked up wires

I watch the video on your site and this make iit very easy to do. That repair that tooks me 40 minutes.

I found that the fill solenoid for the ice maker was down to a drip when energized. I ordered from this site and replaced. now plenty of water, but the ice maker would just stall and jump teeth. The heater which heats the ice up to free it from the mold was defective. Ordered from this site, and now working great.this sitet has good pricing, and the help illustration is great, and explains the sequence of events. This made it easy to troubleshoot. This refrigerator has not give a problem in over 11 years. The problem is "the ice maker". I have replaced it 6 times.

Followed on line video. Also water supply tube on fridge was full of ice. You can pull it out and run hot water on it to clear.

Removed 2 screws that hold ice maker in place. Unplugged and took out of freezer. Used the screws I took out to put new ice maker in. Plugged in the power and in 2 days I had a full ice bin and haven't had any worries since. Should have replaced the broken one along time ago but thought that the process was harder than this. Very easy and suggest this to anyone having ice maker issues. Less than $100 and never have to buy ice for the house again.

It was very simple, used a nut driver to loosen the attachment nuts that held the ice maker in place. Disconnected the wiring harness. Removed the leveling tab from old ice maker and attached it to the new one. Then reassembled in the reverse order. As they say it was no brainer! The best part of the repair, was hearing the ice dump.