25331420102 Kenmore Refrigerator - Instructions

I check why not defrost, y test element and tha problem is defrost timer, i ordered and change, that is it. Your intructions that is very nice.Thanks Ben

Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger

unplug fridge,Then take rack out n remove the 2 screws on the icemaker set aside,then remove 2 screws on the back panel, cut wires n splice in new part! put back the same.

Ordered the new part-Unplugged the refrigerator - took off the cover over the defective timer - put in the new part put the cover back on - plugged the refrigerator back in - so far, so good!~

I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises

jump thermostat,fan and compressor came on, ordered thermo from this excllent parts supplier, part came in 4 days later, it was exact replacement, works exactly right!

Followed Internet video instructions for both parts. Two suggestions: Forget the heat shrink tubing and use electrical tape instead, tubing is short in length and difficult to use unless you have a correct heat gun. Secondly, my timer didn't click twice but due to instructions I could determine that the timing was correct in the operation after the first click. This method could be explained as well as when to start it in connection with usage to be the most efficient in temperature and operation.

Unplug the refrigerator. Removed the right hand top shelf. Used a 1/4" nutdriver to remove rear center mounting screw for Control Housing. Used Phillips screwdriver to remove two mounting screws for timer. Unplug cable from timer and plug it into the new timer. Install the new timer and re-install the Control Housing. Plug in the refrigerator and adjust the timer to start the unit. This was a snap with the diagnostic provided by Part Select. At first I thought it was the fan rubbing but when I removed the cover (two screws) it was obvious that wasn't the problem. The diagnostic hinted that it was either the timer or the motor capacitor making the noise. Because the noise continued after turning OFF the control, I thought it was the timer...I was right.

My husband watched the video on your website and found it very easy to do the repair. The repair company that diagnosed the problem wanted $210 to do it. The part I ordered was under $20, and after he installed it the refrigerator has been working great. We would highly recommend your site to anyone who needs to fix anything!

bottom left cornerof fridge defrost timer replaced two bolts and a wire

Defros timer was easy I finished it in about 15 minuts but the defrost themostat was hard.I had ploblems with the wire conectors and the tape I had to use Twist-on wire connectors.I hope I will not have problems later.So far 1 week later it is working.I can't belive $50 saves me $600.Thanks to Part Select for the video and how fast they shipping my parts in less than 2 days.

Removed old fan motor and installed new one.Not much room for big hands back there.Flexible extensions valuable on this job.

The website said 60% of people with same refrigerator problem solved the problem with a new fan kit. I received the fan kit within 3 days of ordering. Was shipped from Fresno, CA to Long Beach, WA. The fan kit was to be installed behind rear panel in the freezer compartment. When I removed the old fan motor, I noticed the shaft turned harder than the new fan motor, suggesting a problem with the old fan motor. I plugged in the obvious fan motor power bundle with no problem. The instructions and diagram with the kit nearly steered me wrong. Instructions, diagram and splices with the kit instructed to cut the "extra" wire bundle and splice "similar" wires (should have said same color wires). Luckily, I ignored those instructions when I remembered the U-Tube video depicted the extra wire bundle was to be inserted into a factory penetration in the back panel, facing the freezer compartment. This power bundle is for adding an ice maker, which my refrigerator did not have. When reassembled and the refrigerator restarted, I could immediately feel forced air in the refrig, where there was no flow before fixing. I observed that all the refrig and freezer dials do is act like a valve to increase or decrease air flow to the compartments. The dials have no mechanical or electrical connections, just designed to divert air flow from across the cold 'evaporator' fins. I recommend other consumers to remember carefully what they see in the video and watch again if stumped during the job. The video was better than the instructions which may have been written in China or India. I am happy. Repair was a lot cheaper than a new refrigerator and I would not have bought another Frigidaire. Thanks to this website. r. andersen

Replaced thermo-fuse

Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.