All Installation Instructions for Kenmore Freezer 25328459807

Compressor keep running would not cool.frozen coil

As per instructions.removed inside shelves.removed back cover over coil let thaw.removed old thermostat &clips as per instructions.replaced with new.

Parts Used:

Defrost Heater

Mark from SEYMOUR, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

freezer would frost up and not get cold enough to keep frozen.

Removed shelves ,removed panel on interior back wall with Philips screwdriver ,unplugged wire terminals slid thermostat off coil ,then reversed process to complete installation.

Parts Used:

Defrost Thermostat

Richard from SLIDELL, LA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

End cap for side door shelf broken

Both end caps were missing on the door side bottom metal shelf. succesfully installed no tools needed

Parts Used:

Shelf End Cap - Right Side - Tilt-out

wissam farhat from medley, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Piece broken off of drawer slide

I removed the screws and replace the broken slide with the new slide. Put the basket drawer back on the track and it now stays in place and can easily be used once again.

Parts Used:

Drawer Slide - Left or Right Side

Carol from Lawrence, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Freezer wouldn't shut off and wouldn't reach cold enough temperature.

Removed existing part, tested it, found it to be defective. OrderEd a new one and replaced the existing one.

Parts Used:

Defrost Thermostat

Tunis from NOLANVILLE, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Missing key

After removing the key from its shipping package I pushed it into the freezer locking slot and turned it to lock and unlock the lid and then removed it. I had no problems with this fix. Of course, I am an older gentleman with a lot of experience in repairs around my house,as well as other houses. I am sure that a less experienced person may have more of problem with this type of "repair".

Parts Used:

Freezer Door Key

John from DUNBAR, WV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

fan would not turn on

easy change less than 10 min

Parts Used:

Defrost Thermostat

Evaporator Fan Motor (115v)

Freezer Door Key

kevin from NINEVEH, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

broken drawer slide

removed old broken part, 3 screws, then installed new part.....done

Parts Used:

Drawer Slide - Left or Right Side

warren from Farmdale, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Needed a left hand hinge

The left swing hinge (297283901) that i needed is not available anywhere so I bought the right swing hinge (297283900), used a hydraulic press to pop out the pin and move it to the other hole. After that it was real quick to remove the screws and change out the hinge, changing the swing of the door. It is easiest to remove the top hinge and door first when doing this.

Parts Used:

Bottom Hinge

Benjamin from Roseburg, OR
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Fan motor died.

Remove shelves. Unplug unit. Unscrew back panel. Remove wire harness. Remove old fan. Insert new fan. Screw it in. Reattach wires harness. Plug unit in and make sure fan is on.
Reattach back panel. Put shelves back in.

Parts Used:

Evaporator Fan Motor (115v)

Basket Bumper

Yvonne from CORP CHRISTI, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Freezer fine, fridge too hot!

Removed the back panel in freezer compartment with the nut-driver. Then I cut off old thermostat connections, and spliced in new thermostat connections (repairman had already replaced defrost timer, and said not to trust connectors included on wires-they failed often). Then I snapped thermostat itself onto cooler coil. So far so good, fridge is running at 35-40 degrees a week later. Thanks Parts-Select!!!

Parts Used:

Defrost Thermostat

Marc from Chesterfield, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

My Freezer Was Frosting Up, My Ice Maker Was Not Working ,And My Fridge Was Warm.

Had to remove all screws on rear back cover of freezer inside, unplugged refridgerator, uncliped thermostat, unpluged thermostat. Replaced thermostat with new one in the same location, and let defrost fulley. Reassembled, pluged in, and tested. All was good. But I did also replace timer at first part of the repair so I suggest you replace both at the same time.

Parts Used:

Defrost Thermostat

Todd from Kewaskum, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Cooling coils would ice up and fridge would warm up

I removed the shelves in the freezer, took out the five 1/4" screws and lifted off the cover. It was a simple matter of using a blow drier to remove all the ice, then unplugging the two wires and unclipping the thermostat from the upper cooling tube. Then clipped the new one on and reconnecting the two wires.

Works great!!!

Parts Used:

Defrost Thermostat

Richard from Tehachapi, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

the refrig was in storage for about a year, the freezer door warped

removed freezer door and installed the new one. This was a pretty easy thing to do, although putting the old handle on the new door was a challenge. No knowing that there is a plastic piece holding the top of the handle i broke the that piece and had to order another one. Mean while the freezer was making alot of frost inside, so that had to be cleaned after the new part came.

Parts Used: