This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. The run capacitor is attached to the compressor. This part is 120 volts a...
$66.01
In Stock
Order within the next 11 hrs and your part ships today!
This small, Phillips-head screw works with your refrigerator/freezer. It screws in to the freezer door and connects to the door handle. This part is made of stainless steel and is sold individually. T...
$33.08
In Stock
Order within the next 11 hrs and your part ships today!
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
$119.06
In Stock
Order within the next 11 hrs and your part ships today!
This drawer slide supports the left or right hand side of the sliding drawer.
$45.60
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for 25326082100
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jerome
March 29, 2023
how do I access the 9 volt battery compartment
For model number 25326082100
Hello Jerome, thank you for contacting us. Based on our research, there is a battery cover on the right bottom of the toe grill. Remove that battery cover, then you get access to the 9v battery. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Lester
November 30, 2021
Freezer want cool no
For model number 25326082100
Hello Lester, Thank you for the question. if the Freezer is not cooling, we suggest making sure the Evaporator Fan Motor is running normally to circulate the air. We also suggest checking the Door Gasket to make sure it is not damaged and is properly sealing the door. You can also test the Defrost Thermostat. The best way to do this is to remove the thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. We hope this helps!
This freezer has many screws that hold the cover on the back of the door and assist clamping the edge of the gasket in place. Be sure to just loosen the screws 3/4 the way out, use a flat head screw driver to pry the cover from the door in case over time it is stuck to the door. The new gasket will come in a creative box trying not to kink the gasket itself, but there will be some distortion of the gasket when you get it. Put it in the sun or in hot water. I put it in my dryer for 10 minutes. Remove the old gasket, and start at the top of the door to replace the gasket. TIPS: If the screws are backed out enough, there should not be any problem sliding the back part of the gasket under the cover. When on the sides, do not pull the gasket down to make it easier to slide the gasket underneath the cover. This will distort and lengthen the gasket so it will not fit and thin it out so it will not function well. Once the gasket is in place, tighten the screws being sure to feel along the outside edge of the gasket for any bulging that would indicate that portion of the gasket is NOT under the cover properly.
I accidently threw away both freezer keys to our upright Gibson and G.E. Freezers!!!! I had no luck finding replacements locally, so I got on the internet and came across PartSelect.com. I called them on the telephone; and after giving the model numbers of my freezers, the keys were on their way!! I received the keys very quickly and both worked perfectly. I would highly recommend Partselect.com. Charlotte M. Bishop
The repair was as easy as removing three phillip head screws for each slide rail and removing and replacing the broken slide rail. However, over the years, the walls of the freezer had bowed making the drawer a bit short to ride on the new rails -- causing the drawer to fall off the slide rails since the span between each rail was now wider than the basket. To remedy this problem. I used washers and placed them on the back side of each rail where the screws are located . This was the perfect solution compensating for the extra width resulting from the slightly bowed walls in the freezer. This solution allowed the basket to fit on each slide rail without falling off .