25323724101 Kenmore Freezer - Instructions

No repair. The key fit!

Took off cover, unplugged wires, removed old motor, mounted new motor, remounted new motor and replaced cover.

Now need a new control board for same model.

Use the rubber brushing to fill the gap.

Loosened the screws all around the door. easier if you take the door off the unit and lay it on a table. Cover the table with a blanket to protect the door finish. Old gasket just pulls loose. Press the raised bead on the new gasket under the plastic strip. Corners were the most difficult. Retighten the the screws and rehang the door. It took some practice to get the bead under the plastic strip.

freezer section remove ice trays ,shelves,unplug ice tray.use 1/4 nut driver remove back panel,use hair dryer thaw ice from evap coil ,unplug tstat remove install new one.plug in ice maker,put back panel back on ,ice maker and shelves plug refridgerator back in

Easy

1. Ensure that the power is completely removed from the freezer. 2. Using needle-nose pliers and a screw driver, remove the wire retainer holding the controller assembly to the compressor and remove the controller assembly by pulling away from the compressor. 3. Cut the two wires from the existing controller assembly and strip the ends about a quarter of an inch. 4. Slide the heat shrink tubing over the wires of the connector provided with the controller kit. 5. Use the Blue Barrel connectors provided with the controller kit to connect the controller wires provided in the kit to the existing wires of the freezer. **Ensure that they are well crimped. 6. Using a heat gun, shrink the tubing to fit over the connector and wires. **Be careful not to overheat. 7. Plug the connector into the new controller provided in the kit. 8. Plug the controller assembly back into the socket on the compressor. 9. Reattach the wire retainer securely to hold the controller assembly to the compressor. 10. Plug in the freezer and adjust the thermostat so that the compressor energizes. If the controller was the issue your freezer should begin to cool.

We are not handy, we had an appliance repair person install the gasket.

It's easy to know how to use a key. I didn't have a difficult part, I didn't have the model # because I had lost my key and the model # is inside. I was able to find the energy saving paper that came with it but it had four model #'s. I called a couple places and no could me. I pulled up Part Select on line and just thought I would give them a try. I got a very nice person (Jeremy) He went thru every model that I had and three out of the four matched so he sent me a key and if it didn't work I could get my money back. I give him a A+ four taking that extra step, unlike the other places. Very satisfied!

Brought replacement key works just like original I thought it would be metal from reviews but it was plastic and still works perfectly

I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator

Oh yea thanx to partselect it went great didnt get fisrtkey but when got the second key it worked great thanx partselect

Took about an hour previously to deice freezer, timer was running,drain was open, jumped defrost thermostat out and heater was O.K. Defrost thermostat was just a plug and play item, the time involved was in taking the freezer apart to get to it.

First of all thanks to all who posted their stories, because those stories helped me to narrow down what could have gone wrong with my fridge. I did not know how frost-free refrigerators worked at all, reading your stories and doing some on_line research I understood the theory behind the work. My freezer was working constantly, but fridge was warm, cold air would not reach to fridge because freezer was completely frosted.
I had ordered defrost heater, defrost timer and thermostat. I was sure one of these parts was the problem.
First I used flat screwdriver to turn the timer manually untill frdge stopped running(timer is on the left bottom corner behind the black decoratve plastic under the door) . Waited about 20-30 min, checked ,freezer was still frosted. I disconnected the fridge from the wall socket and took shelves out from freezer compartment. This is where hair-dryer came in handy or you could wait till ice would melt on its own, which could take long time.Then loosend 2 screws on left wall that were holding icemaker unit half-way , unplugged the icemaker and took it out. Then took the light-bulb and cover off. Next I unscrewed and took the posts out that were holding shelves in place. Then I took remaining screws from back wall out and gently pulled back cover up then forward a little until I could see electrical connectors behind the cover and unpluged them. Back wall cover was ready to come out. I discovered thick wall of ice covering entire cooling unit. Used handy hair dryer again. When the ice melted, I saw the thermostat was busted open ( Iguess water or moisture got into the unit, then froze and ice pop-openned the cover damaging one of the connecting wires). I diconnected wires and changed the thermostat , which was very easy, just one clip holding it in place . Then plugged the fridge and checked if heating unit was working by touching it. Negative. Closed the door and let fridge run for 15 min, turn timer with screwdriver until fridge stopped working, cheked heater again- wallah it was warm and then it got really HOT! and melted all of the new frost build-up(a sign that thermostat was working). Closed the door waited another 15-20 min, fridge came-on on its own. Unplugged the fridge, pulled it forward from the wall and used sponge to drain the water from holding tray- about one half gallon of it. This is a good time to use a vacuum clener to undust the back and under the fridge. Then put everything back, in reverse order, ofcourse. Cleaned fridge and freezer compartments with warm soap and winneger solution (really good- this was a present to my wife who took our two little daughters to grandmmas and out of my way), put everything back and turned the fridge on recommended settings. Its been 5 days allready and it works great ( I used thermometr to check temperature inside the fridge and freezer). I'm thinking of returning defrost heater and timer back.Thanks PartSelect.Com, I saved lots of money. Hope this story will be helpfull to someone.Thanks for your time!

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .