252411-0672-01 Briggs and Stratton Engine - Overview
Sections of the 252411-0672-01
[Viewing 24 of 24]-
Air Cleaner Assys
-
Alternator Chart
-
Blower Hsg
-
Carburetor Assy
-
Controls
-
Crank Grp
-
Crankcase Cover Cam
-
Cylinder
-
Electric Starter
-
Electric Starter Switch
-
Electrical
-
Flywheels Screens
-
Fuel Pump Grp
-
Fuel Tank Assys
-
Gasket Set
-
Head
-
Muffler Grps
-
Oil Fill Oil Gard
-
Page E
-
Page K
-
Piston Grp
-
Rewind Assy
-
Sno Guard
-
Starter Panel Kit
Keep searches simple, eg. "belt" or "pump".
Puller-flywheel
PartSelect #: PS8905120
Manufacturer #: 19203
This flywheel puller is designed for servicing larger small engines by safely removing tightly seated flywheels without stressing the crankshaft or damaging ignition components. Constructed from heavy...
$33.95
Special Order
Bushing-valve Guide
PartSelect #: PS8924945
Manufacturer #: 231218
This genuine item is supplied by the original equipment manufacturer for use with engines, generators, lawn mowers, lawn tractors, and snowblowers made by Briggs & Stratton, Toro, Lawn Boy, and Murray...
$25.95
Special Order
Key-flywheel
PartSelect #: PS8925657
Manufacturer #: 222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
$5.95
In Stock
Engine Breather Gasket
PartSelect #: PS8941097
Manufacturer #: 27803S
This is a high-quality manufacturer-sourced part which is made for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It helps to distribute the pressure evenly and ...
$7.95
Special Order
Kit-idle Mixture
PartSelect #: PS8941496
Manufacturer #: 292681
This is an authentic replacement part manufactured for use with Briggs & Stratton small engines. The idle mixture kit is used to adjust the amount of fuel that is sent to the engine's intake while the...
$20.95
Special Order
Pulley-starter
PartSelect #: PS8942071
Manufacturer #: 295871
Introducing the Briggs and Stratton Starter Pulley, a vital component for your product repair needs. Crafted with quality and precision, this pulley plays a significant role in your engine's start-up ...
$25.95
Special Order
Seal-governor Shaft
PartSelect #: PS9063527
Manufacturer #: 692407
The governor shaft seal is sold individually and is made out of plastic. A screwdriver, a set of pliers, and a socket set might all be needed during the installation of this item. Over time this part ...
$13.95
Special Order
Screw
PartSelect #: PS9063630
Manufacturer #: 691061
This is an authentic OEM component from Briggs & Stratton. The magneto armature screw is compatible with many lawn and garden engines. The hardened metal screw helps to mount the magneto armature. A w...
$5.95
Special Order
Connector-hose
PartSelect #: PS9063654
Manufacturer #: 691609
This is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is an identical r...
$13.95
Special Order
Common Symptoms of the 252411-0672-01
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gas tank leaking, pull starter rivets worn, rope and rope bushing worn
The gas tank was a simple job, close the fuel shut off, remove fuel hose then back out 2 bolts on the mounting bracket. Reverse procedure to mount.
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill switch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill switch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
Parts Used:
-
Dennis from EUFAULA, OK
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
2 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!