221432-0345-01 Briggs and Stratton Engine - Overview
Sections of the 221432-0345-01
[Viewing 18 of 18]
Keep searches simple, eg. "belt" or "pump".
Puller-flywheel
PartSelect #: PS8905120
Manufacturer #: 19203
This flywheel puller is designed for servicing larger small engines by safely removing tightly seated flywheels without stressing the crankshaft or damaging ignition components. Constructed from heavy...
$33.95
Special Order
Bushing-valve Guide
PartSelect #: PS8924945
Manufacturer #: 231218
This genuine item is supplied by the original equipment manufacturer for use with engines, generators, lawn mowers, lawn tractors, and snowblowers made by Briggs & Stratton, Toro, Lawn Boy, and Murray...
$25.95
Special Order
Key-flywheel
PartSelect #: PS8925657
Manufacturer #: 222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
$5.95
In Stock
Order within the next 3 hrs and your part ships today!
Engine Breather Gasket
PartSelect #: PS8941097
Manufacturer #: 27803S
This is a high-quality manufacturer-sourced part which is made for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It helps to distribute the pressure evenly and ...
$7.95
Special Order
Kit-idle Mixture
PartSelect #: PS8941496
Manufacturer #: 292681
This is an authentic replacement part manufactured for use with Briggs & Stratton small engines. The idle mixture kit is used to adjust the amount of fuel that is sent to the engine's intake while the...
$20.95
Special Order
Pulley-starter
PartSelect #: PS8942071
Manufacturer #: 295871
Introducing the Briggs and Stratton Starter Pulley, a vital component for your product repair needs. Crafted with quality and precision, this pulley plays a significant role in your engine's start-up ...
$25.95
Special Order
Common Symptoms of the 221432-0345-01
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gas tank leaking, pull starter rivets worn, rope and rope bushing worn
The gas tank was a simple job, close the fuel shut off, remove fuel hose then back out 2 bolts on the mounting bracket. Reverse procedure to mount.
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill switch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill switch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
Parts Used:
-
Dennis from EUFAULA, OK
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
2 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!