22102 (1988) Kenmore Range - Instructions

Just put it right into the receptacle. I want to add...we had gone to our local appliance store and brought home a wrong-size unit. Got online and your website came up. It was easy to find the correct part, ordered it and it arrived 3 days later. I have already recommended your website to 2 of my friends. One very good experience!!!

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

Remove the element and pan. Unscrew the bracket holding the old terminal. The terminal has adequate wire to pull out. Found area where insulation wasn't brittle. Cut old wires and stripped them to expose 1/2 inch of wire. Attached wires from new terminal with wire nuts. Placed heat-shrink tubing over each assembly and shrank it with a heat gun. Retained the bracket from the old terminal, since it looked like it would hold the terminal assembly a bit more firmly than the new bracket. Reassembled in reverse order. Presto -- once again disappointing my wife in her desire for new appliances!

Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the correct replacement number on the package. Thanks Part Select.

I lifted the coils, removed the old bibs and replaced them with the new bibs.

All I had to do was remove old drip pans and insert the new ones. What a huge difference it made. It made my stove look so much newer.

After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.

Replaced old drip bowls with the new ones. Very simple, no tools required.

Pulled the elements out and replaced the parts that were missing . Then replaced the elements.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

This is an easy repair and for anyone thinking that they might have trouble effecting it, you all have my assurance that all the heat related elements are easily replaced. These elements are basically plug in and there is a shielded area (usually placed in the northeast quadrant of the burner unit. With everything turned off, pull the burnt out surface element up and toward the southwest. It should unplug from the female receptacle. Installing a new element involves performing this in reverse by coming into the surface with the prongs facing downward towards the receptacle and then pushing towards the northeast and downward at the same time The element should click into place. The entire time necessary to effect this repair should be less than ten minutes.

My GE range is 20 years old, and still going strong. All I needed was to replace the 6" surface unit. After making slight adjustments, it was just a matter of placing the new unit. After finding this Co. on the internet, and checking others, I will certainly order from Part Select again!Dorothy Trakshel

really easy, remove old and replace with new...easy, once you have ordered and received the correct part.