192432-0159-01 Briggs and Stratton Engine - Overview
Sections of the 192432-0159-01
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Puller-flywheel
PartSelect #: PS8905120
Manufacturer #: 19203
This flywheel puller is designed for servicing larger small engines by safely removing tightly seated flywheels without stressing the crankshaft or damaging ignition components. Constructed from heavy...
$33.95
Special Order
Bushing-valve Guide
PartSelect #: PS8924945
Manufacturer #: 231218
This genuine item is supplied by the original equipment manufacturer for use with engines, generators, lawn mowers, lawn tractors, and snowblowers made by Briggs & Stratton, Toro, Lawn Boy, and Murray...
$25.95
Special Order
Float-carburetor
PartSelect #: PS8980404
Manufacturer #: 494381
This is a genuine OEM supplied replacement carburetor float designed for lawn and garden equipment engines. This float controls fuel flow into the carburetor bowl by adjusting the needle valve. Includ...
$25.95
Special Order
Filter-pre Cleaner
PartSelect #: PS8982674
Manufacturer #: 492889
This replacement filter-pre cleaner is a genuine OEM sourced item, not an aftermarket imitation. It is a high quality item commonly utilized on Briggs and Stratton engines. This item adds a extra laye...
$10.95
Special Order
Motor-starter
PartSelect #: PS8983858
Manufacturer #: 497595
This starter motor is for lawn and garden equipment engines.
Starter motor spins the flywheel to start the engine.
Wear work gloves to protect your hands when installing this part.
$196.95
In Stock
Gasket-float Bowl
PartSelect #: PS8945656
Manufacturer #: 281165S
This is a Genuine OEM replacement part used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recomm...
$8.95
In Stock
Cap-oil Fill
PartSelect #: PS8945667
Manufacturer #: 281658S
This manufacturer approved replacement part is specially produced for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is utilized to keep the oil in the t...
$7.95
Special Order
Kit-Oil Gard
PartSelect #: PS8961583
Manufacturer #: 398182
This oil guard kit helps manage oil flow and containment within the system. Designed for durability, it supports proper lubrication and cleaner operation.
$147.95
Special Order
Common Symptoms of the 192432-0159-01
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Cannot pull starter cord out or engine will not turn over
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gas tank leaking, pull starter rivets worn, rope and rope bushing worn
The gas tank was a simple job, close the fuel shut off, remove fuel hose then back out 2 bolts on the mounting bracket. Reverse procedure to mount.
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill switch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill switch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
Parts Used:
-
Dennis from EUFAULA, OK
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
3 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.
Parts Used:
-
Alberto from PALMETTO BAY, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
12 of 46 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!