130902-0213-99 Briggs and Stratton Engine - Overview
Sections of the 130902-0213-99
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Filter-pre Cleaner
PartSelect #: PS8937831
Manufacturer #: 271466
This is an OEM approved replacement part designed for gas trimmers/brush cutters. Its purpose is to filter out dust and debris from the air that goes into the unit. Over time it will get dirty and clo...
$7.95
Special Order
Gasket-fuel Tank
PartSelect #: PS8939191
Manufacturer #: 270073
It is an authentic manufacturer-sourced replacement gasket which is specially designed for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. This component pro...
$8.95
Special Order
Seal-throttle Shaft
PartSelect #: PS8942061
Manufacturer #: 270167
This is an authentic Briggs & Stratton replacement part. The throttle shaft seal is commonly found in small engines, such as those used for yard equipment. This part is made of felt, and is used to ...
$8.95
Special Order
Pulley-starter
PartSelect #: PS8942071
Manufacturer #: 295871
Introducing the Briggs and Stratton Starter Pulley, a vital component for your product repair needs. Crafted with quality and precision, this pulley plays a significant role in your engine's start-up ...
$25.95
Special Order
Gasket-cylinder Head
PartSelect #: PS8941204
Manufacturer #: 272157S
This item is a genuine OEM sourced part that is intended to be used with small engines from Briggs & Stratton and Toro. The gasket is used to seal the connection between the cylinder and the head. A h...
$11.95
Special Order
Common Symptoms of the 130902-0213-99
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
5 HP Briggs and Stratton chipper shredder - no spark
Removed old sparkless magneto, replaced with new part PS9278124 Magneto, and still no spark. The only conclusion that I can draw, is this magneto is defective,
Parts Used:
-
Thomas from ALFRED, ME
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
17 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Could not keep an aftermarket muffler on the engine.
Once I determined what OEM muffler I needed, installation was relatively easy. I have a 1982 4hp Briggs on my Snapper tiller. There was a 90* galvanized elbow coming out of the exhaust port, with a bezel nut to lock it down. Do not remove the elbow, even though it appears that you should. If you install the muffler without the elbow the muffler will parallel the the vacuum for the carburetor and can melt the rubber couplers. Use the elbow to direct the heat away from the carburetor. Use a pipe wrench to lock down the bezel nut because the weight of the muffler, especially under vibration, can work loose and fall down on the tine belt cover and melt it. The bezel nut that comes with the muffler should also be used to lock down the muffler to the threaded intake bracket that comes with the muffler, not to replace the bezel nut for the elbow.
Parts Used:
-
Richard from KERNERSVILLE, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
13 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.
Parts Used:
-
Alberto from PALMETTO BAY, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
11 of 43 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!