130217-3138-XX Briggs and Stratton Engine - Overview
Sections of the 130217-3138-XX
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Gasket-crkcse/009
PartSelect #: PS8939396
Manufacturer #: 270126
This is a genuine Briggs & Stratton and Toro part sourced directly from the manufacturer for use in blowers, engines, generators, lawn tractors, and vacuums. The crankcase gasket is made out of a thin...
$14.95
Special Order
Key-flywheel
PartSelect #: PS8925657
Manufacturer #: 222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
$5.95
In Stock
Order within the next 16 mins and your part ships today!
Gasket-breather
PartSelect #: PS8943888
Manufacturer #: 27549S
This is the gasket that helps to provide an air tight seal for the breather assembly. It is a high quality item that is supplied by original equipment manufacturer for use with Briggs and Stratton and...
$6.95
Special Order
Gasket-cylinder Head
PartSelect #: PS8941204
Manufacturer #: 272157S
This item is a genuine OEM sourced part that is intended to be used with small engines from Briggs & Stratton and Toro. The gasket is used to seal the connection between the cylinder and the head. A h...
$11.95
Special Order
Pulley-starter
PartSelect #: PS8942071
Manufacturer #: 295871
Difficulty pulling the starter rope or a cord that stays extended can result from a damaged recoil pulley. This wheel guides and stores the rope while helping turn the engine during starting. Similar ...
$25.95
Special Order
Common Symptoms of the 130217-3138-XX
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
5 HP Briggs and Stratton chipper shredder - no spark
Removed old sparkless magneto, replaced with new part PS9278124 Magneto, and still no spark. The only conclusion that I can draw, is this magneto is defective,
Parts Used:
-
Thomas from ALFRED, ME
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
19 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old diaphragm dried up
Tore carburetor off leaf blower and replaced. To do that require taking off the air cleaner removing the gas tank and all the brackets holding the controls on it. And keeping track of all the screws and Wires that control choke and throttle. I took several photographs. I did not need all the gaskets and jet’s that were included in the kit but it had what I needed.
Parts Used:
-
Steven C from CENTREVILLE, MI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
6 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.
Parts Used:
-
Alberto from PALMETTO BAY, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
11 of 45 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!