13-3628-00-06 Tappan Cooktop - Overview
Sections of the 13-3628-00-06
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Terminal Block Kit
PartSelect #: PS470125
Manufacturer #: 5303935058
This surface burner terminal block kit comes with interchangeable mounting brackets, terminal box, ceramic wire nuts, heat shrink protective tubing and wires.
$24.46
In Stock
Order within the next 22 mins and your part ships today!
Drip Bowl - 8"
PartSelect #: PS437595
Manufacturer #: 316048413
This drip bowl is located beneath the element and catches any spills. It is sold individually and has a diameter of approximately 10 inches.
$19.75
In Stock
Order within the next 22 mins and your part ships today!
Chrome Drip Bowl - 6"
PartSelect #: PS437596
Manufacturer #: 316048414
This drip bowl is sold individually. This part is located beneath the element and catches spills from cooking.
$18.65
In Stock
Order within the next 22 mins and your part ships today!
Burner Switch Kit
PartSelect #: PS470145
Manufacturer #: 5303935086
This switch controls the stove top surface burner.
$72.50
In Stock
Order within the next 22 mins and your part ships today!
Surface Burner Coil Element - 8" - 2100W
PartSelect #: PS473948
Manufacturer #: 5308011964
Got a faulty burner coil? We've got your back! Here's a genuine Frigidaire Coil Surface Element to the rescue. This replacement part is explicitly designed for the cooking surface of your stove. At 8 ...
$239.34
Special Order
Surface Indicator Light - 250V
PartSelect #: PS436963
Manufacturer #: 316022503
$83.50
In Stock
Order within the next 22 mins and your part ships today!
Surface Control Knob
PartSelect #: PS434405
Manufacturer #: 3051546
Sold individually. This knob accepts a double-flat shaft.
No Longer Available
Common Symptoms of the 13-3628-00-06
[Viewing 3 of 3]Element will not heat
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old pans/bowls were corroded
Very easy---simply unplug the burners, remove the old pans and replace with the new ones
I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
Parts Used:
![](/437596-1-S-Frigidaire-316048414-Chrome-Drip-Bowl-6-amp-quot.jpg "Chrome Drip Bowl - 6" – Part Number: 316048414")
![](/437595-1-S-Frigidaire-316048413-Drip-Bowl-8-amp-quot.jpg "Drip Bowl - 8" – Part Number: 316048413")
-
John from Nisswa, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
48 of 55 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
High heat reluctant to turn down.
Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Parts Used:
-
George from New Port Richey, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
45 of 49 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right front burner would over-heat
First of all I removed the top panel then removed the switch. I then took pictures of the switch & drew a sketch with all the info. Then I went to your web site, matched up the switch & ordered.
When the switch arrived I went thru the above replacing the bad switch.
When the switch arrived I went thru the above replacing the bad switch.
Parts Used:
-
Melvin from Attica, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
23 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!