110C66012011 Kenmore Dryer - Instructions

I was afraid I had to go in from the back panel, undo a million little bolts, after pulling the whole thing out far enough to get behind the dryer. Not so! I watched the installation video. I cannot get to the 220 plug easily so I turned of the switch at the breaker box. I opened the small panel on the front of the dryer under the dryer door. Loosened one bolt on a cover guard to expose the element. Unplugged the connection to the element and easily pulled out old part. Slipped in the new part, reconnected the little plug connections, closed cover panel.! Voila! Done! My Husband was amazed that I was done & we were ready to go again & my grand kids cheered for me!! 15 minutes or less instead of hours.

Just took the old one out and slipped the new one in! That's it! That easy. Thank you!

Disconnected power from dryer (safety first)! Removed bottom front panel (two screws hold it in place). Then remove the two screws that hold the sheet-metal bracket/guard in place in front of the heating element. Disconnect the two wires from the heating element terminal (white stripe wire is on top, remember for re-install purposes). Remove screw that holds heating element in place. Remove heating element from the vent housing. NOTE: The old heating element will be difficult to remove, it's a tight fit AND there's a spring on its' side that holds it tightly in place...beware that the edges are sharp; I used a pair of pliers to pull the element out in order to protect my hands. Once the old element is out, put the new one back in its' place...again watch out the edges are sharp and the element fits tightly into the vent, so if you have mechanics gloves now's the time to put them on to protect your hands, as the edges of the vent and element are sharp. Once the element is into place, secure into place with screw on left side, re-attach wires (white stripe on top terminal), put the guard back into place, close up the bottom panel, and power up.

Pretty easy to fix, hardest part was having to get the screws out of the inside of the dryer to replace the sensor itself. Once that was done it was pretty quick! PLUS super fast shipping on my part!! Was fixed before any repair places even called me back!!

I purchased a new heating element installed and stil had same problem. I order the 2 sensor (kit) located in same area and that took care of problem. I should have purcahsed all at same time like someone else told us in the website. Thanks parts select for the very fast delivery

I needed a schematic to know exactly where the heating element was located and to be sure of what the part looked like. I found the part and after watching the video on removing and installing the heating element decided to replace the High Limit Thermostat and fuse as well. I also read some of the other reviews. The part arrived in 2 days and I did have a little help removing the old one before the parts arrived. Since the dryer was ready for the new parts when they arrived, the install was easier. I had a little trouble balancing the flashlight to see well enough and realized it was easier to put the element in then reinstall the unit, it was a little tricky getting the element sleeve back into the slot, THEN screw the thermostat and Thermal fuse onto the element housing. Since everything was open, I vacuumed all the lint out that I could, hooked up the vent hose, plugged the unit in and pressed the button. I then basked in the glow of a working heating element and I was back in business!. Thanks for the video and help. I LOVE PartSelect.

Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.

After trying to follow a very detailed description by another consumer, we googled our washer and found a site that showed step by step direction that took us through removing all panels and getting to the bellow easily. Not removing the proper panels, we found was making the job hard!I believe the site was applicance services...very helpful! Step by step literally!!Cost of parts through parts select reasonable.

diognostic suggested thermal fuse or thermistor. Thermistor tested low resistance (<2K olms). Replaced thermistor and dryer heat returned.

First I reviewed the diagram to become familiar where items were located. I then insured unit was unpluged I used nutdriver to remove front cover from dryer. Noticed a lot of lint. Good time to vacuum it made finding screws and wires easier.Next Located heating element as described in parts location diagram. Utilized small socket to remove screws in cover plate. the socket set allow easy access to screws under cover plate. Removed 2 electrical wires from heating element. Pull heating element from housing with needle nose pliers. Had to tug a little, inspected element and found break in heating coil.Placed in new element by using reverse installation procedure. (didn't replace lint)This was an easy fix and I saved lots of dollars on repair or hundreds on new dryer. I spent about 20 minutes on the entire project. If you can read you can do this project. Very easy to complete. PS Ordering the parts was easy and arrived earlier than exepected.

removed bottom panel & removed old element.

flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.

The repair was easy and very simple. With nut driver removed front cover. Noted the wiring set up and removed. Lifted heat tunnel up and pulled it from the case. Removed the old heating element and install new one. Reinstalled the heat tunnel reconnected the wires. Slide tunnel back into position. Replaced screw and you are done. I always pray and ask Jesus for his help and things always go well.

I removed the front lower cover to the unit, located the heater and removed that. I installed the new unit and closed everything back up.

Removed existing parts and replaced with new high limit thermostat and thermal fuse kit,replaced flue and tested. Worked like a charm.