11086983300 Kenmore Dryer - Instructions

I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful

PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might contact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.

My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you

Did an Ohm test on the old Thermal Fuse found it to be bad. Replaced it with a new and the dryer is back to working great. Your suggestions saved approximatley $150.

Thanks for the help.

Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.

I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.

I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.

Popped the lower cover off the dryer, found the thermal fuse and thermostat mounted on the heating tube. Removed the screws with a nutdriver, swapped wires to the new parts, and reinstalled. Then I spent 30 minutes vacuuming 13 years worth of lint and crud out of the machine - it was pretty gummed up in spots, which is probably the cause of the failure.
I have a 25 foot run of hose from the dryer outside, so I replaced that with 4" metal ducting. Clothes dry much faster now!!! Maybe my electric bill will go down (fat chance :) )

I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.

Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.

When the problem first came up, I took the dryer apart without first looking up any instructions. This wasn't difficult, but didn't realize when removing the fan from the motor, there is a square lug as part of the fan hidden by the rear clamp securing the motor. I was able to remove the fan by holding the motor shaft with a crescent wrench and removing the fan by hand, but was difficult and gloves were necessary in case the fan loosened quickly and my hand came in contact with the sheet metal (very sharp).

I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.

This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.

The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.

My dad was ready to spend $2000 on a new washer/dryer (he has to have a matching set!). Anyway, his dryer would not generate heat. A google search turned up partselect.com, which walked me through the procedure to see what we needed.

It turned out to be a simple to replace $25.00 part! The dryer is drying as if it was brand new. Saved $1,975. Hehe.

Thanks, partselect!

I saw some videos suggesting you remove the back panel.Then I saw a video where only the kick plate was removed and the element was removed that way.
I removed both the back panel and kick plate.At first I thought I was wasting my time however once I got started I was glad I removed both back and front.
There was a significant amount of lint in the bottom of the dryer which made it easier to remove.
It also made it easier to remove the heater element.
I hope this helps.

I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screws back in and fastend the front back on and were in bussiness!

Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.