This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.
$45.05
In Stock
Order within the next 11 hrs and your part ships today!
This dryer drum roller kit is designed to restore smooth and quiet operation in a wide range of dryer models. It includes two drum rollers, four tri-rings, and one to two retaining washers, providing ...
$28.95
In Stock
Order within the next 11 hrs and your part ships today!
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$17.01
In Stock
Order within the next 11 hrs and your part ships today!
If your dryer drum isn’t spinning, the motor might be the issue. This replacement motor works with many Whirlpool-brand dryers made before 1996 and comes with the pulley already attached. It powers th...
$149.79
In Stock
Order within the next 11 hrs and your part ships today!
This dryer door handle is designed to facilitate smooth opening and closing of the dryer door. Measuring 5-3/4 inches by 2 inches, it features a white, smooth-surfaced finish that complements most dry...
$62.56
In Stock
Order within the next 11 hrs and your part ships today!
Brighten up your appliance with this easy-to-install 10-watt light bulb, perfect for dryers and refrigerators. It gives off a clear, steady light so you can easily see inside when the door is open. Wh...
$25.95
In Stock
Order within the next 11 hrs and your part ships today!
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.
$46.44
In Stock
Order within the next 11 hrs and your part ships today!
This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is no...
$49.45
In Stock
Order within the next 11 hrs and your part ships today!
This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 4" wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers.
$51.40
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for 11077132412
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Vincent
May 31, 2023
Have replaced the moisture sensor, gas soleniods, cycle thermostat, high end thermostat, thermal fuse. Goes thru a proper cycle, heats up fan works fine, no lint issues blows hot air out the exhaust. Why will the clothes not dry completely on any setting?
For model number 11077132412
Hello Vincent, thank you for reaching out. We believe your dryer is having this problem because of the faulty radiant flame sensor. We recommend you replace the flame sensor, part number PS11741429, to fix the issue. We hope this information helps!
Pryed dryer top open and opened front door. . Unscrewed the 2 retaining screws. Pulled old switch from the wiring harness. Put new switch in place and replaced the retaining screws. Put new switch wire plug into the wiring harness. Before closing top, checked door switch function with dryer on. Dryer cut off when door open and when closed dryer started normally. . . Maint. Note instruction book should warn that letting door slam, which I did on occaision, broke the switch arm. Might save future problems.
It was simple once I figured out what to do:). I removed the 2 screws on the top of the dryer... they were a bit hard to find. Even with the other descriptions on this site. I was removing things I didn't need to. The 2 screws you need to remove are under the LINT COLLECTOR LID. Remove those 2 screws & lift the lid... it will be tight at first. the front of the lid has 2 "catches" in the corners.
The hardest part was getting the door switch assembly to "unplug". We pried it off -- eventually -- & then simply plugged in the new one.
Saved me LOTS of money & was worth the 30 minutes - 1 hour of work.
As I said previously, once you realize how to get the lid up & manage to pry off the plug, that's all there is to it -- easy!
