11076132411 Kenmore Dryer - Instructions

i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service

Pryed dryer top open and opened front door. . Unscrewed the 2 retaining screws. Pulled old switch from the wiring harness. Put new switch in place and replaced the retaining screws. Put new switch wire plug into the wiring harness. Before closing top, checked door switch function with dryer on. Dryer cut off when door open and when closed dryer started normally. . . Maint. Note instruction book should warn that letting door slam, which I did on occaision, broke the switch arm. Might save future problems.

It was simple once I figured out what to do:). I removed the 2 screws on the top of the dryer... they were a bit hard to find. Even with the other descriptions on this site. I was removing things I didn't need to. The 2 screws you need to remove are under the LINT COLLECTOR LID. Remove those 2 screws & lift the lid... it will be tight at first. the front of the lid has 2 "catches" in the corners.

The hardest part was getting the door switch assembly to "unplug". We pried it off -- eventually -- & then simply plugged in the new one.

Saved me LOTS of money & was worth the 30 minutes - 1 hour of work.

As I said previously, once you realize how to get the lid up & manage to pry off the plug, that's all there is to it -- easy!

Save yourself time & money & do it yourself!

Grow a second set of hands. Always unplug any appliance. Remove lint screen. remove two screws (philips Head). I took a wooden shim lightly tapped w/hammer to pop front of dryer top free. Mine worked on hinges and just flipped back til it rested against the wall. Removed two 5/16 screws inside holding face on carefully raise face section off the support clips at either side on the bottom. Pull drum out (I have the large style drum commercial size [approx.). Clean the inside free of all lint (known to be fire hazard). Sling new belt around drum. Get newly grown set of hands to hold drum in place. Pinch belt to fit between tensioner, lift tensioner and place belt around motor pulley. Spin drum couple times to make certain belt isn't twisted. Reverse dismantle proccess to put back together. Replace all parts that come with kit, you'll feel better knowing you got a new dryer, almost.

First unplug your dryer. Then, I removed the two screws on the lint trap leaving the lint trap in place--do not pull out the lint trap--only remove the two screws. Next, slide the top of the dryer slightly forward in order to release the top of the dryer. I did this with my hands. Once the top of the dryer is released, raise the top of the dryer and unplug the door switch assembly. Then, remove the two screws that hold the switch. These two screws were located on the front panel of my dryer and are visible when you open the dryer door. Remove the old switch and install the new switch by putting the two screws you previously took out from the old switch back in place and plug in the new switch. Lower the dryer top. Push the top back to lock in place. Line up the lint trap holes for the two screws that hold it in place and replace those screws. Plug your dryer back in and it should work properly. Very easy repair. We ordered our part one morning before noon, and it was here the next afternoon with regular shipping. GREAT SERVICE.

After looking on the website for advice I walked throught the simple steps of disassembling the front, removing the drum, removed the back, disconnected the wire harness. Then removed the blower housing in the back. The blower, mounted on the back side of the motor was very tight. I used a pipe wrench wedged in place and help by my 10 year old Grand-daughter while I used an adjustable wrench to turn the shaft on the front of the motor. Spun the blower off, removed the two clips holding the motor. Then reversed the process when I received the new motor. Care should be taken to avoid damaging the blower fan if a lot of pressure is required.

1st Unpluged power.
2nd removed two screws under lint screen cover.
3rd poped up lid with flathead screwdryer, then removed (2) 5/16 screws from door cover and unpluged lid switch, lifted up dryer door pannel
4th removed drum
5th took out plastic triangle wheel rings
6th removed old belt guild (to motor pully)
7th removed old wheels and plastic rings stops
8th cleaned excessive hair dust with shopvac
9th put new replaicment part in dryer. made sure to turn manually to make sure belt was lined up properly, then put all dryer peices back.
10th aditional work, took back cover off and removed the (4) 1/4 screws for lint screen case (left side in dryer) vacumed out any excessive dirt lint ect, also cleaned any excessive dust I found in back of dryer, dryer , exhaust ect, and put all back together.
JUst like a new dryer aain after all PM was complete.

Replacement handle snapped in place very easily.

I read a fix-it article from another contributor and followed those instructions to the T. Pull out lint trap, remove the two screws. Slide the top cover towards the front and prop it up with a mop handle.
Unscrew two screws in the door switch (with the door open) - Oh, to keep from killing yourself unplug the dryer just in case. Take pliers and pull the plug apart. It will be right in front of you in the right corner at the top. Plug new switch into that plug, reinstall the switch by reinstalling the two screws you removed. Snap top back into place and reinstall the two screws at the lint trap. Oh, don't forget to clean the trap and slide it back into the unit. Now you have earned that beer.
Put tools away and proudly show your job off to the wife telling her how difficult it was.

This was my first dryer repair, and it was so easy. Simply pull out the lint trap and unscrew the two screws that are exposed. They attach the top deck of the dryer to the drum.

Once it's unscrewed, pull forward while lifting the top of the dryer. The top is attached to the control assembly. They should both lift up, but you'll need something to prop it up like you would the hood of your car.

Next, use the pliers to pinch the connector so that you can separate the two parts of the connector.

Open the dryer door to gain access to the screws that hold the switch in place. Use your screwdriver to unscrew the switch.

Plug the new switch connector in, and close up the dryer.

Word of caution; there are sharp edges inside the dryer so be careful.

took the old one off and pooped in the new one!

super fast shipping, got the part in two days, and had it done in 15-20 min, remove the front pannel, remove the belt and tenssioner,took the drum out , took the old rollers , lubed the shafts,replaced the old rollers with the new ones, intalled the drum back, the tenssioner and the new belt, reinstalled the front pannel, and done...easy and fast job, like new dryer, works nice...save some money...the new one will do the same..just dry the clothes.

Pryed the top off the dryer, unplugged the door switch, took the screws out of the front panel, then lifted the drum out. Placed the new belt around the drum and while my wife held it in place and steadied it, I reached underneath and looped the belt through (as per instructions), reassembled and back in business! Reaching under the drum was not that easy....VERY tight space to work in and there was no way I could get both hands through, I almost gave up, but one last try and a couple of good grunts, and it popped into place. Getting the wires back on the door switch was a bit of an ordeal too. Took about 30 mins. but still worth it. I'm sure I saved at least a $100 repair.

It was really quite esy remove the screws from the back and pop the top off . then remove 2 top inside screws from the front , lift the front off the sides , support the drum and lift out , you will then see the idler wheels, replace them with the new ones ,replce the tensioner , wrap the belt around the drum, need help putting the drum back in the case, have someone hold the drum in place while you lay on the ground and put the belt around the motor pulley and the tensioner on the bottom.you then put the front panel back into place and secure with the 2 inside screws, then put the rest back together in reverse oder. ... hope this helps someone

Follow the advice given in the partsselect website. However, while removing the blower, my hand slipped into the housing and cut my thumb. Connected the wires to the junction box on the motor but didn't realize that the contacts would hit the drum when reinstalled. The original junction box was at a 90 degree rotation relative to the new box. When trying to test the breaker tripped. Using the multitester I found out that I burned out the thermal fuse, and froze the door switch. I replace both those parts and started the dryer and could hear a grinding sound. Inspection revealed that the housing of the motor was rubbing against the drum. Removing the drum yet again, I rotated the housing and replaced the drum. The dryer was finally working well.