11076132411 Kenmore Dryer - Instructions

First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.

Remove the lint screen, then remove the two (2) Phillips screws that are at the entrance of the lint screen compartment. Take a putty knife and insert it under the top pannel of the dryer about 1” in from the outside and push the putty knife in as you lift that corner of the pannel. Repeat on the other side. Then raise the lid and prop it up. The door switch is on the right side just behind the door on the inside. Open the door and remove the two screws that hold the switch and remove the switch. Install the new switch like the old one came out and close it up you’re ready to go! It is very easy you can’t hurt anything.

Replacement handle snapped right back in place. Took about 2 seconds.

First removed lint screen, then removed screws holding lint screen housing.Pushed on back of machine a little so that top could be pried up. Then replaced switch and put everything back together. Helps to have two people so one can push on back of top piece while top of machine is being pried up.

I removed the two screws underneath the lent trap the removed the two screws that held the dryer switch assembly. I then lifted up the top and disconnected the door switch assembly. Removing the door switch assembly was the toughest part, and it was not difficult. Simply grab a pair of pliers and pull. I the attatched the new door switch assembly and the four screws and my dryerwas as good as new. I paid around $20.00 including shipping and saved myself a couple of hundred dollars

Removed old door switch and tested with ohms meter. It registered as charged, but when black button was pushed it did not cut off (go to zero). Replaced the part just like the video showed. Only problem i had was dropping my screwdriver down into the dryer well. It was doing no harm so i left it there since i tried retrieving from the back but was not able to get entire back off!

After getting the part and sizing up what to do. I removed the 6 1/4 hex nuts from the back. I removed the 2 hinge nuts 3/8 and popped the lid of the dryer up. It wasn't coming up all the way. I removed the lint filter and removed the two #1 Phillips screws that held the lid to the duct and it came up easy.The switch itself was clipped together and came apart with ease. 2 #1 Phillips screws held the switch in place and quickly tightened down the new switch. I clipped the new switch to the old lead and just reversed the order putting it back together. The light worked and the drum stopped when the door was opened during the cycle. The part matched perfectly and there was no guess work about clearance. It was an easy repair.

Determined that the door switch was not making contact. Removed the lint screen, removed two screws in the lint screen housing, pulled the top of the dryer up at the front of the dryer. This provided access to the door switch which was mounted on top.

The brightness of the light was because the door switch was allowing too much current to the light bulb when the door was open but the switch would not swich the current to the dryer motor when the door was closed. After a day or so of this bright light it burned out. I removed the two screws on top that hold the lint trap in place then I could access the switch by sliding the top of the dryer forward and lifting the it as you would lift the hood of a car. The switch is on the right side and plugs into a three wire connector and only fits in one way. Cheap and easy fix after unplugging the dryer from the wall power outlet.

This was super simple - even I could do it! I followed the 3-step instructions which basically described how to hold the new handle and pushed it into the holes in the door. Less than 30 seconds and no tools.

Followed the video and it was perfect. Easy repair that took under 15 minutes. Great, clear process that was perfectly easy.

I followed the you tube instructions. Unplugged the dryer. Removed the lint screen. Unscrewed 2 screws. Used puttty knife to open the top of dryer. Located the door switch and unplugged it and replaced with new part. Closed top. Replaced two screws and put lint filter back in. Plugged dryer in and turned it on. It worked like new. I'm a woman and this is second part I've had to replace on this dryer. Watch you tube video.

followed the very handy installation video. it was easy to repair the door switch as the drum did not stop when it was opened. glad we used your service and would certainly use it again if needed for other items. your prompt attention to shipping was also appreciated. thank you!

I followed the accurate video. I'm sure I saved a lot of money over having a repair man come out. Now maybe my wife will believe that I am capable of repairing some things myself... eh, probably not.

Did as your video instruction. To me the order of work needs attention: Remove the switch, unscrew 1st, then remove the hook and wire connection. Installation: connect the wire first, then hook to the frame, the last step is screw in the switch. That should prevent accident dropping the switch inside the dryer.