This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If ...
The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt att...
This idler pulley assembly includes the pulley and bracket, ensuring proper tension on the dryer drive belt for smooth drum rotation. Compatible with several Whirlpool, KitchenAid, Maytag, Jenn-Air, A...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
Is your clothes dryer acting up? Don't worry. We've got the solution you've been looking for - the Whirlpool Dryer Idler Spring, a genuine OEM part compatible with select models of Whirlpool, KitchenA...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
September 20, 2022
How do you remove the top and front panels?
For model number 11068132410
Hello David, thank you for the great question! Remove the end caps of the control console, there are two small tabs to release. You will need to move the control console by unscrewing two screws and then pulling it gently forward and lifting up. That will give you access to the screws for the top panel underneath it, there should be no need to disconnect any of the wiring harness in the console. Slide the top panel forward and lift. Be careful, it is awkward! To remove the lower access front panel, press the spring clips between it and the door panel, about three inches for the sides and it will pop forward so you can lift it up and away. If you also want to remove the front door panel and bulkhead assembly, first unhook the two springs underneath the panel (as well as any wiring that you see for the door switch, for example) and then unscrew the two screws on the bottom of the door panel, and then the two on the top and it should lift free. We have included a YouTube link that might assist you with this, as it describes removing these parts at the beginning! Good luck with your repair.
Was this helpful?
Thank you for voting!
Robert
October 25, 2022
What is the part number for the lint screen?
For model number 11068132410
Hi Robert, thank you for reaching out to PartSelect. We have researched the model you have provided and have found that the part you are looking for is part number PS11731421. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
Dryer quit drying. What coil, etc do I need to repair and what is cost and time to deliver.
For model number 1106802310
Hello Tom, thank you for reaching out. If the dryer is running but not drying clothes, the issue might be a faulty heating element. We would suggest checking it, the part number is PS11770230. We hope this information helps!
Grow a second set of hands. Always unplug any appliance. Remove lint screen. remove two screws (philips Head). I took a wooden shim lightly tapped w/hammer to pop front of dryer top free. Mine worked on hinges and just flipped back til it rested against the wall. Removed two 5/16 screws inside holding face on carefully raise face section off the support clips at either side on the bottom. Pull drum out (I have the large style drum commercial size [approx.). Clean the inside free of all lint (known to be fire hazard). Sling new belt around drum. Get newly grown set of hands to hold drum in place. Pinch belt to fit between tensioner, lift tensioner and place belt around motor pulley. Spin drum couple times to make certain belt isn't twisted. Reverse dismantle proccess to put back together. Replace all parts that come with kit, you'll feel better knowing you got a new dryer, almost.
1st Unpluged power. 2nd removed two screws under lint screen cover. 3rd poped up lid with flathead screwdryer, then removed (2) 5/16 screws from door cover and unpluged lid switch, lifted up dryer door pannel 4th removed drum 5th took out plastic triangle wheel rings 6th removed old belt guild (to motor pully) 7th removed old wheels and plastic rings stops 8th cleaned excessive hair dust with shopvac 9th put new replaicment part in dryer. made sure to turn manually to make sure belt was lined up properly, then put all dryer peices back. 10th aditional work, took back cover off and removed the (4) 1/4 screws for lint screen case (left side in dryer) vacumed out any excessive dirt lint ect, also cleaned any excessive dust I found in back of dryer, dryer , exhaust ect, and put all back together. JUst like a new dryer aain after all PM was complete.
1) Disconnected power cord from wall. 2) Disconnected vent hose from back of dryer. 3)Removed dryer rear panel. 4)Disengaged tension spring on idle wheel arm. 5) Removed worn idle wheel. 6)Installed new Idler wheel assembly. 7) Vacuumed dust from rear of dryer (optional, recommended). 8) Reinstalled rear cover, vent hose and power cord. Easy repair 15-30
