This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. It has two ports for water to pass through: a large one, and a s...
Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature or amount of water needed.
If your washer door won’t close or lock, or your machine won’t start, this door latch might be the issue. It’s the part that keeps the door shut tight during the cycle and makes sure everything runs s...
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place o...
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is...
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
This drain hose carries wastewater from the washer’s pump to the household drain, helping your machine empty properly during each cycle. It’s a reliable replacement when the original hose is cracked, ...
$54.84
In Stock
Questions And Answers for 11047532601
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dave
February 2, 2023
Replaced pump but comes up with code F30 won’t let water in
For model number 11047532601
Hi Dave,
Thank you for your question. The F-30 error code indicates a dispenser system error. This can occur when the linkage between the dispenser motor and the dispenser has failed, if there is a loose wiring connection between the central control unit and the dispenser motor, or if the dispenser motor has failed. If the dispenser motor makes a clicking noise when it turns or if it turns continuously, then it has failed and will need to be replaced. If the dispenser motor is fine and everything else checks out, then you will need to replace the central control unit. If you have any questions, please let us know. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Michael
November 3, 2023
Start button when pushed will not start machine. Ran through the diagnostic test and all worked but the button works was working but very finicky until now won’t start the machine
For model number 11047532601
Hello Michael, thank you for contacting us. Based on our understanding of the issue, we would suggest checking the control board, part number PS11746714, to solve the problem. We hope this helps!
Washer will turn on with add garment light on and lock door but won't start a cycle. Won't unlock door even if stop button is pushed - - add garment light will flash. Error code F28 has come on. Washer is drained. Washed a bunch of towels and F22 light went on and drained tub. Then on next load washer stopped at 1 minute, wouldn't unlock, wouldn't turn off. Unplugged unit for 30 minutes, then plugged back in, then turned on: Washer will turn on with add garment light on and lock door but won't start a cycle. Won't unlock door even if stop button is pushed - - add garment light will flash. Won't turn off.
For model number 11047532601
Hello James, thank you for your question. The F28 error code indicates a communication error between the control boards. Check the connections. There are three screws on the rear of the top panel that secure the top on. Once removed, the top will slide back and come off to be set aside. In the right front corner near the front control panel is the main machine control. Remove each connector, one at a time, and replace into the control. This will rectify any connection issue if there is one. Once each connector has been reset into position, remove the back panel from the machine to access the motor control board. Do the same for each motor connector. Plug the machine back in and see if the code returns. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find anything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module.
