This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.
$225.28
In Stock
Order within the next 45 mins and your part ships today!
Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$96.35
In Stock
Order within the next 45 mins and your part ships today!
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Order within the next 45 mins and your part ships today!
Also known as a door boot seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately...
$320.26
In Stock
Order within the next 45 mins and your part ships today!
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
NOTE: Per Manufacture, belt measures 48.22" long uninstall...
$67.39
In Stock
Order within the next 45 mins and your part ships today!
This is the replacement bellow clamp for your washer. It approximately 16 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place on t...
$41.14
In Stock
Order within the next 45 mins and your part ships today!
Order within the next 45 mins and your part ships today!
Questions And Answers for 11042932200
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
ROBERT
December 7, 2023
Timer readout starts blinking with 11 minutes left Washer stops, has to be reset
For model number 11042932200
Hi Robert, thank you for contacting us. We would recommend checking the user interface board, part number PS11744914. It processes the cycle settings you choose. You may need to replace it to fix the issue. We hope this sorts out your problem!
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door. (3) I packed towels under the washer. (4) I slowly removed the cleanout in the front of the pump, using the water vac to catch the water as it leaked out. (5) I removed the wiring to the motor. (6) I removed the screw that holds the pump in place with a Torx T-20 socket. (7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ). (8) I tested the pump and found it would run but was making a lot of noise and running slow. (9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4). Don Kramer Wichita, Kansas
1. remove the three screws from the top backside of the top panel 2. push the top panel to the rear 1/8 to 1/4 inch 3. lift/rotate top panel from rear to front, set aside. 4. remove the three wire connectors from latch. 5. use #15 Torx to remove the three screws from the latch. 6. remove and replace part using top opening. 7. reverse order to finish.
Pulled out machine...removed top panel..unscrewed existing valve and removed it...then reversed the whole process with the new valve..it was very easy to do and worked perfectly...no more water in tub!