This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$15.95
In Stock
Order within the next 5 hrs and your part ships today!
This kit includes one driver hub and two driven basket hubs. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced.
$47.81
In Stock
Order within the next 5 hrs and your part ships today!
This kit helps your washer spin smoothly and quietly again. It includes everything you need—bearings, drive shaft, seal, grease, and more—to fix issues like loud noises or poor spinning. If your washe...
$155.15
In Stock
Order within the next 5 hrs and your part ships today!
This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. Customers have rated this repair as easy. To c...
$55.71
In Stock
Order within the next 5 hrs and your part ships today!
Having a problem with a funky-smelling washing machine, or one that just doesn't seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This p...
$25.31
In Stock
Order within the next 5 hrs and your part ships today!
This drain pump assembly removes water from the washer during the drain cycle. If your washer isn’t draining properly, replacing the pump may be necessary. Ensure compatibility with your model before ...
$151.24
In Stock
Order within the next 5 hrs and your part ships today!
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$141.25
In Stock
Order within the next 5 hrs and your part ships today!
When it's time to replace the Drain Pump Hose on your Whirlpool appliance, we've got exactly what you need. Our genuine Whirlpool Drain Pump Hose is designed specifically to help your washer do its jo...
$29.92
In Stock
Order within the next 5 hrs and your part ships today!
You better be confident in your repair abilities before you try this. Get the washer to a large open area, like your garage, because there are a lot of parts. Take off the back, pop the top, unsnap and remove the top ring off outer tub, take out the agitator, take out the inner tub, disconnect the pumps and electrical wires, take screw out of rotor on bottom and remove rotor, take out 4 bolts to remove motor magnet ring, and now you may be ready to unhook the outer tub from the 4 supports (springs) and lift it out of the metal frame. Then unscrew the bottom nut on the shaft, use blocks to hold the tub in place, and carefully tap the old shaft and bearings out. The instructions that came with the kit helped. The shaft and top seal comes out the top first. Then you can tap out upper bearing and then the lower bearing and spacers.Instructions called for a special tool to install the bearings but you can carefully tap them in. You will need blocks to support the tub while you tap them. First block under the tub and install top bearing, then flip over and use several blocks to hold tub while you drop the shaft, spacers, and tap lower bearing in. I did not need to tap on the inner ring of the bearings, just the outer ring. Be very careful not to damage the seal in the bearings. That's why you must tap them in careful and slow. Them install the nut on the bottom. You need to hold the shaft with damaging it while you tighten the nut. I used the hard nylon gear from the inner tub which I was replacing with a new one. Then put it all back together.
Removed a cap in the center of the tub basket which has a bolt that needs removed I believe it's a 9/16 after I removed the bolt I then removed the center of the bottom of the basket assembly which then allowed me to get to the basket hub that needed replaced it was a little dirty and I couldn't get it out so I sprayed a little penitrating oil on it let it sit a little then I was able to remove the hub and install the new one then I put it all back together and the washer is working great
3rd time replacing this part. The plastic grooves against the metal get wore down. Only 20$ to repair ! Take off the 3/8 bolt - center pops out. Remove screws pop out old piece and tighten new piece each side evenly.
