110280 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer making lot of noise during spin cycles
6 of 10 people
found this instruction helpful.
-
Michael from SAVANNAH, MO
- A Bit Difficult
- 1- 2 hours
-
Socket set
Removed agitator and basket hub parts and cleaned all parts of agitator then replace basket hub with new basket hub kit according to video ran washer but did not solve problem
Was this helpful?
Thank you for voting!
The capacitor exploded, broke the plastic cover that held it to the body of the machine and blow itself clear of the wires
4 of 4 people
found this instruction helpful.
-
Jay from AMELIA CT HSE, VA
- Very Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I removed the back access panel and what was left of the capacitor mounting device (the capacitor (or what was left of it) was laying against the access panel). I mounted the new capacitor which had a metal strap for mounting. I removed the small, black, wire mounting device that was still plugged in to the old capacitor and slipped the
... Read more
wires through that device. After reviewing how to reattach the wires (it turned out the polarity on my capacitor did not matter) I plugged the wires in using the wire mounting device. Once I closed it back up everything worked fine.
Read less
Was this helpful?
Thank you for voting!
Lid wouldn't lock
4 of 4 people
found this instruction helpful.
-
James from INDIAN LAKE, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!
Was this helpful?
Thank you for voting!
tub motor shot
5 of 7 people
found this instruction helpful.
-
melanie from GREENFIELD, IN
- Really Easy
- 30 - 60 mins
Please check the order was refused so I would not have to pay to ship back. The lady I spoke to on the phone said to do it this way. I have been TRYING to call for 2 weeks but no one is answering the phone due to CV19!!
The order is back at your warehouse. Please give me my refund!! Plus I have emailed your CS dept. numerous times wi ... Read more th NO answer, only automated.
The order is back at your warehouse. Please give me my refund!! Plus I have emailed your CS dept. numerous times wi ... Read more th NO answer, only automated.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
No cold water being put in the washer
4 of 4 people
found this instruction helpful.
-
Marylou from SOUTH ELGIN, IL
- Easy
- 30 - 60 mins
-
Nutdriver
Turn off the water. Disconnect both hoses. Remove the plug from the outlet. Remove five screws with a nut driver from the back panel. Remove the back panel. Remove two screws from the cold water valve. Pulled out the old valve. Install new valve with the two screws. Reinstall back panel with the five screws. Reset codes to the washer. Tes
... Read more
ted out washer. Works fine.
Read less
Was this helpful?
Thank you for voting!
rod came loose from one upper suspension bushing
4 of 5 people
found this instruction helpful.
-
Norman from MOBILE, AL
- Really Easy
- 30 - 60 mins
Per your directions. Note that part has been updated from original. Looks like an improvement, adds tab to grab rod, but changes installation.
Was this helpful?
Thank you for voting!
making noise when starting spin cycle
4 of 5 people
found this instruction helpful.
-
JERRY W. from CARROLLTON, GA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Watch video on the site and the insulation will be easy and take about 30 min.
Was this helpful?
Thank you for voting!
The washer would walk across the floor
4 of 5 people
found this instruction helpful.
-
William from BROOKFIELD, WI
- Very Easy
- 30 - 60 mins
-
Socket set
Watched the video. It was by far the easiest repair I've ever done. The washer is happy and stays in it place
Other Parts Used:
Was this helpful?
Thank you for voting!
Cracked housing
4 of 5 people
found this instruction helpful.
-
John from Durango, CO
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Turn off and unscrew hot -cold hoses and drain line. Unplug power and pull unit away from wall. Tip onto front of machine and lean it onto something that will give you enough room to work as the pump is on bottom left back of unit. Unscrew all back plate screw's and remove back panel and keep screw's handy. Three main screw's hold pump in
... Read more
place but loosen hose clamp's first and its out. Reverse what you just did and you should be good to go! Good Luck!!
Read less
Was this helpful?
Thank you for voting!
Washer -Maytag Centennial- would NOT agitate. It would run through all cycles as indicated by the lights and even spin at the end, but never agitated. It also did not appeared to go into "sensing" mode at the start. Took a long time to move from "sensing" light to "wash" light. Did not hear or see a
3 of 3 people
found this instruction helpful.
-
Maxwell from RINGWOOD, NJ
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
There are a number of videos showing how to do this repair:
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut dri ... Read more ver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.
I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut dri ... Read more ver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.
I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
Read less
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people
found this instruction helpful.
-
Helen from NASHUA, NH
- Really Easy
- 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
constant out of balance indicator light and loud vibration noises
3 of 3 people
found this instruction helpful.
-
Donald from BEAUMONT, TX
- Really Easy
- 30 - 60 mins
-
Screw drivers
Watched U-TUBE VIDEO of suspension rod replacement for whirlpool top loading Cabrio washing machine.
Was this helpful?
Thank you for voting!
wasn't cleaning very well
3 of 3 people
found this instruction helpful.
-
Brian from GREENBRIER, AR
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Went with the instructions
Other Parts Used:
Was this helpful?
Thank you for voting!
Noisy during spin cycle
3 of 3 people
found this instruction helpful.
-
Robert from ORLANDO, FL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Repair was pretty straight forward with the exception of removing the agitator. Hint, do not force it, just continue to work it until it releases. Problem was not entirely corrected, but improved.
Was this helpful?
Thank you for voting!
Lid lock not working.
5 of 9 people
found this instruction helpful.
-
James from LIVONIA, LA
- Very Easy
- 15 - 30 mins
-
Socket set
Followed instructions.
Was this helpful?
Thank you for voting!