110280 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loose pulley
7 of 11 people
found this instruction helpful.
-
Joseph from BAKER, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Tightened up the pulley as the video showed me that might be the issue.
Other Parts Used:
Was this helpful?
Thank you for voting!
washing machine stuck on drain cycle
17 of 41 people
found this instruction helpful.
-
Matthew from Wauwatosa, WI
- Easy
- 15 - 30 mins
-
Screw drivers
Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.
Was this helpful?
Thank you for voting!
When the washer goes into a spin cycle, I would hear an intermittent loud clattering noise. I think the clutch teeth above (the cup part that is spring loaded) and the belted pulley's teeth below are not fully seating on each other during the spin cycle.
8 of 14 people
found this instruction helpful.
-
TERRY from WAUKEE, IA
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
W10721967 Splutch Cam Kit
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm ... Read more nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm ... Read more nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Read less
Was this helpful?
Thank you for voting!
heavy loads did not spin dry properly
6 of 8 people
found this instruction helpful.
-
Chet from CLEARWATER, FL
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer was out of balance on spin cycle
5 of 5 people
found this instruction helpful.
-
Charles from Grizzly Flats, CA
- Easy
- 1- 2 hours
-
Pliers
I do not know much about washer repair and after watching how to replace the suspension rods I decided it was not as difficult as I thought. I replaced the suspension rods and springs and that fixed the problem. The price for parts was reasonable and I received my parts in 2 days.
Other Parts Used:
Was this helpful?
Thank you for voting!
Grinding noise from the gearcase.
5 of 5 people
found this instruction helpful.
-
D from DISTRICT HTS, MD
- Very Easy
- 1- 2 hours
-
Screw drivers, Socket set
Actually, I "Youtubed" it. I entered the info from the washer and found what was similar. What would help is when you tilt the washer (on back or front) so you can look at what you're going to work on to match (or closely match) what is on Youtube. It is SO easy, it's unbelievable.
Was this helpful?
Thank you for voting!
Very wet clothes after load was complete
5 of 6 people
found this instruction helpful.
-
Craig from CRARY, ND
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Remove the center cover with a screwdriver then loosen the 7/16 bolt with an impact driver socket ccw to remove completely biggest issue is removing bottom cover tried pick tools only thing that was succesful was some dawn dishsoap on the center bolt area to loosen enough to lift up the cover replace the hub part that had worn spline groo
... Read more
ves remember to use blue loctite on the 7/16 bolt before re-installing cw to tighten bolt
Read less
Was this helpful?
Thank you for voting!
The washer stopped draining.All the pump motor did was hum.
5 of 6 people
found this instruction helpful.
-
Michael from Staten Island, NY
- Easy
- 1- 2 hours
-
Pliers, Socket set
I drained the machine and pulled it away from the wall.Then I disconnected the drain hose and removed the back panel.Next,I removed the three screws holding the pump in place and disconnected the power plug from the motor.I then removed the short drain hose from the pump.Installation was the opposite of the removal sequence,and the machin
... Read more
e worked fine right after I was done.The new part was identical the the old one,and the job was a snap.
Read less
Was this helpful?
Thank you for voting!
Whirlpool cabrio would not go into the spin function without triggering an error code of 5d
5 of 6 people
found this instruction helpful.
-
Victor from HOUSTON, TX
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed the center cover of the agitator with a flathead. Removed the nut of the agitator main cover. Had trouble taking the cover off because of the crud holding it down I wiggled it up gently alternating n,s and e,w until I eventually saw it separating from the bottom of the basket. Once it came off you could see how nasty the old hub a
... Read more
ssembly looked. Took the screws off the old hub assembly and removed it. Matched it up with the correct new hub assembly cause the kit comes with 2. Cleaned the shaft and that general area. Installed the new hub assembly, replaced the covers. Ran the drain and spin cycle and it worked with no problem. There are videos on YouTube that show you too. DO NOT try to pry the agitator cover if it won’t rise up easily. Be patient and it will come out.
Read less
Was this helpful?
Thank you for voting!
the splines were worn out on the hub assembley
5 of 6 people
found this instruction helpful.
-
Johnny from NORTH JUDSON, IN
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
screw driver and a rachet and socket took it off and put the new one on . no problem follow the direction that comes with it .
Was this helpful?
Thank you for voting!
Water kept running
5 of 6 people
found this instruction helpful.
-
Marco from LIPAN, TX
- Easy
- 30 - 60 mins
-
Socket set
Safety First unplug unit, close water valves, remove upper panel with a 1/4 inch socket. Remove two screws holding the valve unplug 2 wires and replaced valve with the new one
And very impressed with the fast quick delivery of the part thank you very much
And very impressed with the fast quick delivery of the part thank you very much
Was this helpful?
Thank you for voting!
Washer shook extremely hard Always was off balance
4 of 4 people
found this instruction helpful.
-
Steven from BARNEGAT, NJ
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I purchased the suspension rod kit Installed it What it safe and easy job.
Excellent video thank you
Excellent video thank you
Was this helpful?
Thank you for voting!
The washer was vibrating very bad on large loads
4 of 4 people
found this instruction helpful.
-
Mark from SAINT CLOUD, FL
- Very Easy
- 30 - 60 mins
-
Screw drivers
Using the parts I ordered and following the instructions provided in the video from partselect.com made the repair very easy and solved the problem
Other Parts Used:
Was this helpful?
Thank you for voting!
Making a loud noise for a while then stopped spinning
4 of 4 people
found this instruction helpful.
-
Lucas from ARKANSAS CITY, KS
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this helpful?
Thank you for voting!
Cold water valve sensor no good
5 of 7 people
found this instruction helpful.
-
Robert from STAMFORD, CT
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Took off washer body 6 screws
Took off old sensor installed new
Very simple and smooth
Took off old sensor installed new
Very simple and smooth
Was this helpful?
Thank you for voting!