110280 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
washer is unbalanced during a spin cycle
7 of 7 people
found this instruction helpful.
-
Tiffany from NORTH OLMSTED, OH
- Really Easy
- Less than 15 mins
I watched a video on you tube before making the repair, there was only one bad rod support, location right rear, I recommend watching a video on you tube first, it is very simple to change, however the replacement of the part was not the solution to the unbalanced load during the spin cycle, so I guess I have some research to do.
Was this helpful?
Thank you for voting!
washer wasn't spinning after rinsing but the motor was running
8 of 10 people
found this instruction helpful.
-
Terry from HANCOCK, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
Was this helpful?
Thank you for voting!
I followed the video guide, which was excellent
7 of 7 people
found this instruction helpful.
-
Richard from NAPLES, FL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.
Machine works great now.
Machine works great now.
Was this helpful?
Thank you for voting!
Unbalanced Load
7 of 7 people
found this instruction helpful.
-
Kenneth from SANFORD, NC
- Really Easy
- 30 - 60 mins
I followed the video instructions provided. However, I used the hook on an old rod to pull the new rods through the corner holes in the top of the dryer. Simple invert the old rod and feed through the hole, hook onto the new rod and lift through the hole. It enabled me to lift the tub with one hand and put the plastic seat and new rod
... Read more
in place with the other hand. Too easy and sped up the repair job.
Read less
Was this helpful?
Thank you for voting!
After removing the bolt on top of the agitator, it agitator was very difficult to get out.
7 of 7 people
found this instruction helpful.
-
John from SALEM, VA
- Very Difficult
- More than 2 hours
-
Screw drivers, Socket set
I watched the repair video on Partselect, it was very informative. In the video the agitator lifted right out easily, I was not so lucky. It took me and another gentleman about 4 hours to get the thing out. I watched other videos on ideas to remove, still no luck. Finally I cut the strap off of a carry all bag and was able to get it in a
... Read more
round the agitator and slide it under it. After getting it under the agitator we were able to pull up on it and get it loose.
The rest of the repair was simple, cleaned everything, installed new part, and now washing machine is working like new again.
The rest of the repair was simple, cleaned everything, installed new part, and now washing machine is working like new again.
Read less
Was this helpful?
Thank you for voting!
When washer would go into spin cycle it would shake violently. This also prevented the spin cycle from completing leaving clothes soaked
7 of 8 people
found this instruction helpful.
-
Jonathan from NEW BRAUNFELS, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Followed videos sent with the repair items. It was very easy and solved my issue. My washer did not have the centering springs to begin with so I was unsure if I even needed them. But after replacing all the suspension rods and adding the pack of centering springs this has solved my issues
Other Parts Used:
Was this helpful?
Thank you for voting!
Making noise when spinning tub hit side of washer.
7 of 8 people
found this instruction helpful.
-
Ernestine from CARRIERE, MS
- Really Easy
- 30 - 60 mins
-
Socket set
Remove top of washer suspension
Rod goes on side of tub .
Rod goes on side of tub .
Was this helpful?
Thank you for voting!
washer wasn't spinning on final spin
7 of 8 people
found this instruction helpful.
-
Terry from HANCOCK, MD
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
First I found and reviewed videos on line to do the repair for my machine and when I actually did it the videos made it simple to do. Always look for videos of the installation for your machine or appliance and the job will go easy
Was this helpful?
Thank you for voting!
The wash cycle made a loud grinding noise when it went from filling to wash.
6 of 6 people
found this instruction helpful.
-
Angelo from PORTLAND, ME
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover wi ... Read more th Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover wi ... Read more th Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Read less
Was this helpful?
Thank you for voting!
Washer gets stuck on Rinse and not complete the cycle.
6 of 6 people
found this instruction helpful.
-
Charles from SEALY, TX
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Found common diagnosis and instructions on internet. It is not difficult to replace.
Unfortunately, this new latch assembly did not fix the problem.
Unfortunately, this new latch assembly did not fix the problem.
Was this helpful?
Thank you for voting!
Suspension rods were worn; washer is 10+ years old
7 of 9 people
found this instruction helpful.
-
William from NAPERVILLE, IL
- Easy
- More than 2 hours
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Replaced the suspension rods, suspension rod supports, main drive belt, tub centering springs, water supply hoes, and washer drain hose. Taped new front suspension rods to side of tub to ensure that they did not slide down when raising the washer off its back from the floor. Had a helper lift the tub, which made attaching the new suspensi
... Read more
on rods easy. The tub is extremely heavy so by a helper lifting it up it made attaching the new suspension rods much easier. IMPORTANT: According to the technician's manual, which was taped to the inside of the washer, it is absolutely necessary to recalibrate the washer after replacing any suspension parts. We did this by following the instructions in the tech manual. Failure to recalibrate a washer could result in poor performance. The procedure is different for each brand or model of washer, but again is absolutely essential after replacing suspension parts of any kind. For some unknown reason, our washer did not have the tub centering springs. Our model should have had the springs.Facing the washer, we attached one to the front left tub housing and one to right rear of the tub housing. Recommend that anyone watch the installation videos for the suspension rods, center springs, and main drive belt before attempting the repairs.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Gear stripped on main spline
6 of 7 people
found this instruction helpful.
-
Bernard from ARIZONA CITY, AZ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.
Was this helpful?
Thank you for voting!
Lid lock/latch stuck closed
6 of 7 people
found this instruction helpful.
-
David from BELMONT, MI
- Really Easy
- 30 - 60 mins
-
Nutdriver
Watched a video
Was this helpful?
Thank you for voting!
Washer out of balance
7 of 10 people
found this instruction helpful.
-
Gregory from LAKE ELMO, MN
- Really Easy
- 30 - 60 mins
This was a very easy cure for the problem,
Was this helpful?
Thank you for voting!
Rock and roll on spin
6 of 7 people
found this instruction helpful.
-
Bruce from LANDENBERG, PA
- Easy
- 30 - 60 mins
-
Nutdriver
Replaced the suspension rods.
Must be done on its side as the rods only pull down. There is no slot.
Must be done on its side as the rods only pull down. There is no slot.
Was this helpful?
Thank you for voting!