110280 Kenmore Washer - Instructions

All Instructions for the 110280
31 - 45 of 228

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Making loud noises.
21 of 30 people found this instruction helpful.
  • Roy from BROOKLYN, NY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you
Was this helpful?
Thank you for voting!
My washer lid lock light kept blinking and the washer would not start
17 of 18 people found this instruction helpful.
  • Janice from GREENVILLE, NC
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
I followed the online video, removed the old part and replaced it with the new part. My washer is working perfectly. It took about an hour to reset.
Was this helpful?
Thank you for voting!
Washer would vibrate and bang viciously in the spin cycles
21 of 33 people found this instruction helpful.
  • Jerry from YORK, PA
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
Remove agitator and replace hub. I also recommend replacing the Suspension too. I could tell the hub was bad the piece of metal washer on the bottom was gone. The suspension lost a lot of its stiffing
Was this helpful?
Thank you for voting!
Noise, all the lubricant had leaked from the gearcase.
15 of 15 people found this instruction helpful.
  • larry from SOD, WV
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
DO NOT do this repair from the top. The only thing needed to be removed from the top of the machine is the agitator and retaining clip. After removing these items, lay the machine on its front, on a table if you have a friend who will help. Remove the back cover. Simply disconnect the wiring, remove the water pump, the tub locking mec hanism, the belt, and motor. Remove the four bolts holding the gearcase. It should come out with little effort. Remove the old tub seal. There should be a new one on the replacement. Lubricate the new seal. Dishwashing liquid worked great. Move the drive wheel from the old gearcase to the replacement part. All the parts originally removed will only fit one way. Reverse all the removal steps and you be should be ready to go. My only problem with the replacement was there was no groove in the new part spline for the tub retaining clip. Seemed to be no problem since the agitator is bolted on so the tub is going nowhere.
Was this helpful?
Thank you for voting!
Washer lid would not release
18 of 26 people found this instruction helpful.
  • Michael from BURLINGTON, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplug washer. Remove 4 screws from the small plates that hold top to body of washer. Remove cover plate from back of top. Lift top from base and support it on its back. Remove lid lock mechanism. Unplug connector from its socket at the back of the lid. In reverse order install the new lid latch,
Was this helpful?
Thank you for voting!
Smelled a burning odor occasionally
17 of 23 people found this instruction helpful.
  • Paul from E NORTHPORT, NY
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Socket set, Wrench (Adjustable)
First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting wash er back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.
Was this helpful?
Thank you for voting!
coin in drain pump put a hole in casing
15 of 19 people found this instruction helpful.
  • jon from hannibal, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set
unscrew all the screws on the back of your cabrio washer just the bottom portion to access the drain pump which is located on bottom left underside of the wash drum, the drum on mine is plastic or plastic shroud i guess , theres 3 screws that hold the pump into place, also 2 hose clamps, and the power source, the cap that covers the power source is a bit of a pain to unsnap do this part last cause you'll be able to pull it out from under the drum and get to it easier. once the pump is free just do everything in reverse and you'll be good to go in about 30 to 40 mins . one more thing dont try to caulk or seal on the one thats broke its a lost cause just replace it and make sure like i have been lol no coins left in your pockets before they get washed......whirlpool cabrio other number i got off sticker besides model number is type 580 hope this is helpfull
Was this helpful?
Thank you for voting!
Banging all the time during rinse as if its out of balance
14 of 18 people found this instruction helpful.
  • christine from SWANSEA, MA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Followed the video, no need to add. Worked perfectly!
Was this helpful?
Thank you for voting!
Washer shook violently during spin cycle
12 of 12 people found this instruction helpful.
  • Bobby from LAGRANGE, OH
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Raise top cover, remove tub ring.
Remove suspension rods one at a time by pulling the
rods upward, remove keepers at top,pulled rods out the bottom by tilting washer. Replaced all four rods and installed load centering springs which hadn't been installed from factory. Took 1/2 hour and works like a new one??
Was this helpful?
Thank you for voting!
lid would not lock, washer would not run...
12 of 13 people found this instruction helpful.
  • John from Hale Center, Texas, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix...
Was this helpful?
Thank you for voting!
Lid Lock broke
12 of 13 people found this instruction helpful.
  • Judith from SAYRE, PA
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Socket set, Wrench (Adjustable)
Followed video from you tube. Man made it look very easy. Not! Hole that lock has to come through in back was very tricky. Also, DO NOT THROW OUT OLD PART UNTIL NEW ONE IS INSTALLED. The reason for that is there is a CLIP at the end of the old part that is needed to attach new part to wire section in control panel. NO WHERE is it m entioned at you got the clip from the old part. Luckily we saved it. Without that clip, you are screwed.
Was this helpful?
Thank you for voting!
my daughters ferret chewed little pinholes in the pump hoses
13 of 17 people found this instruction helpful.
  • jeffrey from chicago, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
two small compression clamps hold the hoses in place. these are very simple to remove, however to reinstall the new hoses you should unscrew the pumps with a nut driver, secure the hoses with the clamps, and then screw the pump back to the bottom of the drum. oh yeah make sure to put the back plate back on the machine
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
The tub would spin but it was weak. The splines were stripped on the drive hub.
11 of 12 people found this instruction helpful.
  • Doug from EAU CLAIRE, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Pulled the agitator, un-screwed the drive hub, cleaned the splines on the transmission, vacuumed the debris out of the tub. The repair video said to put towels or something down in the tub so if you drop a screw it will catch it. Put it back together and re-calibrated it. It didn't want to go into the calibrate mode until i moved the mode switch all the way to the left and then right first. Good quality factory parts!
Was this helpful?
Thank you for voting!
Drain Pump Leaking
10 of 10 people found this instruction helpful.
  • Shaun from Central Valley, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Was pretty strait forward. Took the back panel off, removed the 3 mount screws and 2 clamps on the pump, and swapped it all out. Only thing, Paid for 2 day air shipping, took a week for the part to come in. But it was still faster and cheaper then my local parts dealer.
Was this helpful?
Thank you for voting!
All Instructions for the 110280
31 - 45 of 228