110280 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
squeal and chirping while in risne / spin mode
10 of 10 people
found this instruction helpful.
-
Thomas from GRAIN VALLEY, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this helpful?
Thank you for voting!
Washer wouldn't start - Flashing Lid Light
13 of 20 people
found this instruction helpful.
-
Marc from HOPE MILLS, NC
- Easy
- 30 - 60 mins
-
Screw drivers
I checked out the reviews and the recommendation of these "professionals", replaced the part easy enough when it came in. However, it didn't solve the problem. Got an actual professional to come in and see what the problem was, and they determined that gear oil was being leaked and it wasn't worth replacing.
Tried to get a re ... Read more fund and return the part. Was told absolutely not. The money back guarantee is a lie.
Tried to get a re ... Read more fund and return the part. Was told absolutely not. The money back guarantee is a lie.
Read less
Was this helpful?
Thank you for voting!
Washer would not start due to lock mechanism turning on and off.
15 of 27 people
found this instruction helpful.
-
Dyleena from HOUSTON, TX
- Really Easy
- 30 - 60 mins
-
Screw drivers
Dismantled washer lid to install new locking mechanism.
Was this helpful?
Thank you for voting!
Unlevel code. Would not complete spin cycle.
10 of 12 people
found this instruction helpful.
-
Robert from MORGANTON, GA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
First replaced four basket spring supports. Next tried Basket hub assembly ( which showed wear, but not total solution). Next replaced the rotation sensor that's on the stator. That finalized the issue.
Was this helpful?
Thank you for voting!
leaking water pump
10 of 12 people
found this instruction helpful.
-
Houston from Ocoee, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
The most difficult problem was to identify where the leak was and I tried to repair the old pump but that was a waste of my time. I was most impressed with this company in how fast the order was taken and the perfect part was shipped to me. I received the part in approx. 30 hours after I placed the order. The part was delivered by FedEx
... Read more
press to my front door. A very reasonable price for the part. Anyway, most anyone could have done the repair that I did without difficulty.
Read less
Was this helpful?
Thank you for voting!
Slow leak from a cracked drain pump
10 of 12 people
found this instruction helpful.
-
Sarah from Olympia, WA
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
I wasn't able to turn the washer on it's side or front, and instead had to prop it slightly up on cinder blocks due to the configuration of my laundry room. The actual repair was fairly simple, had the clamps supplied been easy to manuever, but they were not. The clamp that goes around the hose from the pump into the inlet valve wouldn't
... Read more
go down around the valve where it was supposed to. I had it too far up, so when I ran the washer, the whole hose popped out and flooded my laundry room. My husband suggested a better clamp, the type that actually opens and you can tighten with a screw system. $2.16 at Lowes. 2nd attempt at repair was successful, and so far no leaks. So...save yourself some time and when you get the replacement pump, take those clamps over to Lowes or Home Depot and buy a clamp that you can open fully, slip over the valve, and tighten as much as you need. If I had that type of clamp to begin with, this project would have taken an hour, tops. And by the way, I'm a 36 year old woman with NO experience fixing appliances, but plenty of experience paying other people too much money to fix things that never should have broken in the first place!
Read less
Was this helpful?
Thank you for voting!
wash machine walked
9 of 10 people
found this instruction helpful.
-
Elzoria from FROSTPROOF, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
watch utube instruction.easy repair
Was this helpful?
Thank you for voting!
Wouldn’t drain pump made loud noise
10 of 13 people
found this instruction helpful.
-
REED from BUCHANAN, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench (Adjustable)
Removed old drain pump and found a sock in the inlet - must have burned out pump because after removing it pump was still defective. Installed new pump in about 30 minutes and off to the races no more issues
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people
found this instruction helpful.
-
Larry from HICKORY, NC
- Very Easy
- Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Read less
Was this helpful?
Thank you for voting!
replaced drain hose that was missing
12 of 20 people
found this instruction helpful.
-
Delmar from EAST TROY, WI
- Really Easy
- 30 - 60 mins
-
Pliers
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this helpful?
Thank you for voting!
drive hub splines were warn off. Thus no agitation was possible. Coins from laundry probably made increased friction to cause excessive ware on the splines.
8 of 8 people
found this instruction helpful.
-
Wayne from HILTON, NY
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
Force the thin nylon strap around and down into the perimeter of the agitator. Draw it snug to the center. The strap must be long enough to make a complete loop up to the top of the tub. Insert a fairly stout wooden stick through the loop so that an upward prying motion of the stick applies a vertical force on the agitator. While the
... Read more
force is applied pound on the lower part of the agitator so that it will break it free from the motor's axel. Of course remove the center bolt first after removing the small hub cover.
Applying liquids to the connection did not help. Just a steady upward force and a few rubber hammer blows to the lower part of the agitator di the trick.
Applying liquids to the connection did not help. Just a steady upward force and a few rubber hammer blows to the lower part of the agitator di the trick.
Read less
Was this helpful?
Thank you for voting!
Slow Spin Cycle with Fast/Normal Agitator
8 of 8 people
found this instruction helpful.
-
Michael from AURORA, CO
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Socket set
My spin cycle was running, but spinning slowly and not drying my clothes. The agitator spun quickly like normal, but the basket did not spin fast. It seemed like something was slipping. I checked the belt, but it seemed fine and it was less than a year old. I was afraid that the transmission was going, but there wasn't any grinding sound
... Read more
of gears. Luckily the hub part description said that this could fix the slow Spin cycle. Over all the repair was easy, but pulling the agitator off was very difficult. I've got a strong grip and patience and after about 10 - 15 mintues of yanking on the agitator it came off. Don't try to use pliers as it will damage the plastic agitator. Replacing the hub drive and reassembly went very smoothly. The old hub drive wore out because it is plastic and connects to the metal drive shaft from the transmission. After years of torque, the hub will eventually strip out. Sooner depending on your usage and heavy duty cycles. In case you don't know, your machine might have the service manual in it on the inside of the body taped to the side. Mine helped me run through some troubleshooting steps and component tests to pinpoint to problem. Thanks Parts Select!
Read less
Was this helpful?
Thank you for voting!
F51 error code
8 of 9 people
found this instruction helpful.
-
Edgardo from SALEM, OR
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Pretty easy! Just follow this link on how to fix the problem:
https://www.youtube.com/watch?v=_-Hg8rLGiKQ
The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be.
https://www.youtube.com/watch?v=_-Hg8rLGiKQ
The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be.
Was this helpful?
Thank you for voting!
During the Spin cycle the washer was noisy and moved around
8 of 9 people
found this instruction helpful.
-
JOHN from HERNANDO, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I watched the video and did exactly what they said to do. It was really easy. The key to the success was in the parts that were mailed to me it had a separate piece of paper telling you to "reset" the washer after doing the repair. I missed this when I watched the video. That was a critical part of the repair which required no
... Read more
tools to accomplish.
I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!
I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!
Read less
Was this helpful?
Thank you for voting!
Shaking extreme
7 of 7 people
found this instruction helpful.
-
Barbara from RICHMOND, IN
- Really Easy
- 15 - 30 mins
-
Socket set
Per instruction sent with purchase
Was this helpful?
Thank you for voting!