110280 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No agitation
3 of 3 people
found this instruction helpful.
-
Jim from ACUSHNET, MA
- Very Easy
- 15 - 30 mins
Pop center cover off wash plate. Remove bolt. Lift off washplate. Slide retainer off with screwdriver and hammer. Slide new retainer on. Replace washplate.
Was this helpful?
Thank you for voting!
washer was draining but no spinning
3 of 3 people
found this instruction helpful.
-
JOSE from MILLBURY, MA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.
Then reverse the operation to stall the new part. Very easy.
Was this helpful?
Thank you for voting!
uneven washer load shaking violently
3 of 3 people
found this instruction helpful.
-
Michael from COLORADO SPGS, CO
- Easy
- 15 - 30 mins
-
Pliers
Followed you tube instructions from parts select and previous owners suggestions to install the right corner suspension rod second.
Was this helpful?
Thank you for voting!
A leaking water pump
4 of 6 people
found this instruction helpful.
-
Connie from Woodland, CA
- Easy
- Less than 15 mins
-
Nutdriver, Socket set
Have the Maytag washing machine little over2 years and the water pump cracked - very disappointed.
Anyway, removed the back panel, unhooked the hoses, used 5/16 wrench to loosen up the screws, unplugged the power connector than replaced it with a new water pump.
It was an easy repair that I taught my 18 yrs old.
Anyway, removed the back panel, unhooked the hoses, used 5/16 wrench to loosen up the screws, unplugged the power connector than replaced it with a new water pump.
It was an easy repair that I taught my 18 yrs old.
Was this helpful?
Thank you for voting!
Stripped screws on a hub drive replacement
3 of 3 people
found this instruction helpful.
-
Bruce from GLOBE, AZ
- Easy
- 15 - 30 mins
-
Screw drivers
Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I alre
... Read more
ady had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well.
Read less
Was this helpful?
Thank you for voting!
water leaking under washer
4 of 6 people
found this instruction helpful.
-
Scott from Wyckoff, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
removed back of washer. turned washer on its side .removed the 3 screws holding pump and the 2 hoses and the electric connection pump came right out. did the reverse to install the new one.stood up the washer and ran it to check for leaks.no leaks installed back of washerand done
Was this helpful?
Thank you for voting!
Burning smell, ASSUMED it was the belt
4 of 6 people
found this instruction helpful.
-
James from MAHWAH, NJ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this helpful?
Thank you for voting!
washer shaking
3 of 3 people
found this instruction helpful.
-
Oralia from DALLAS, TX
- Easy
- 30 - 60 mins
-
Pliers
the repair went well but I still haven't received a refund for the order was was sent incorrectly. Order #22085769 order date 2/3/23
Was this helpful?
Thank you for voting!
Washer walking during spin cycle
3 of 3 people
found this instruction helpful.
-
Tricia from HARLEYSVILLE, PA
- Easy
- 30 - 60 mins
-
Socket set
Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF ... Read more I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF ... Read more I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
Read less
Was this helpful?
Thank you for voting!
Making bumping noise during agitation cycle
3 of 3 people
found this instruction helpful.
-
Stephen from GRAND SALINE, TX
- Really Easy
- 30 - 60 mins
-
Pliers
Watched the video first thing really helpful. Unplugged the machine popped the top put the front left rod on first then right rear that had the clip for the pump hose then the left rear saved front right for last got pretty stiff and it was easier to get to than the rear ones. Put top back down checked level plugged back in and went to wa
... Read more
shing. Worked great so far.
Read less
Was this helpful?
Thank you for voting!
Washer was making an awful screeching noise when agitating
3 of 3 people
found this instruction helpful.
-
Kristy from Lebanon, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this helpful?
Thank you for voting!
washer would not spin on wash cycle
3 of 3 people
found this instruction helpful.
-
Kim from MOUNT UNION, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
My daughter is the handy one in the family. She followed Steve's video installation steps and in an hour i was washing clothes.
Was this helpful?
Thank you for voting!
Actuator clicking not going into spin mode
3 of 3 people
found this instruction helpful.
-
Courtney from Hollis, NH
- Easy
- 30 - 60 mins
-
Pliers, Socket set
I laid the washer on its front side to access underneath. I removed the original washer pulley system and actuator very easily to replace them with the new parts. The new/updated model actuator for my machine was a little bit challenging to maneuver around existing parts to make work, but I eventually got it installed. The plug was angled
... Read more
very differently than the original plug on the actuator, but it was a tight fit. There was no issue installing the washer pulley system. Hooked washer back up to power, water lines, drain line, and the washer has been working perfectly since.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Wash plate spinning. Clothes not spun out.
3 of 4 people
found this instruction helpful.
-
Gregory from GREENFILD TWP, PA
- A Bit Difficult
- 1- 2 hours
-
Socket set
Royal pain getting the wash plate off. I'm 6 foot 215 lbs with muscular arms( beer belly too) and I could not get it to come off. Put hay bail twine around the edge and pulled up so hard the entire machine came off the ground. Luckily I am married. Yep I pulled one end of the string and her the other and it flew off. Part select was $10 c
... Read more
heaper than whirlpool and was a perfect match. I might order another to have because like stated earlier I'm married. She is married to me and the washer and dryer.
Read less
Was this helpful?
Thank you for voting!
Whirlpool Cabrio top load washer Error UL
3 of 4 people
found this instruction helpful.
-
Sheree from Clarkston, MI
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
Lived about 6 months with noisy, unbalanced, vibrating top-load washer that would not fully drain clothes or finish a spin cycle.
Watched as many You-Tube repairs videos as we could. Had difficulty trying to open the top panel for access to spin tub.
Discovered that we had clips in front, about 6" from each side, tha ... Read more t needed pressure push with flat metal paint scraper, in order to open the top for access.
Other than that delay, took us about 2 hours total with two of us working together. In the end, Suspension Kit was exactly what we needed, and NO longer get the UL error code, with bothersome constant spin stops, which failed to spin water out of wet clothing.
Watched as many You-Tube repairs videos as we could. Had difficulty trying to open the top panel for access to spin tub.
Discovered that we had clips in front, about 6" from each side, tha ... Read more t needed pressure push with flat metal paint scraper, in order to open the top for access.
Other than that delay, took us about 2 hours total with two of us working together. In the end, Suspension Kit was exactly what we needed, and NO longer get the UL error code, with bothersome constant spin stops, which failed to spin water out of wet clothing.
Read less
Was this helpful?
Thank you for voting!